선박용 고망간강 소재 파이버 레이저 Bead on Plate (BOP) 실험적 연구(PART 2 : 아르곤,헬륨보호가스)
Experimental Study of High Manganese Steel Material for Ships Fiber Laser Bead on Plate (BOP) (PART 2 : Argon & Helium Shielding Gas)
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Environmental regulations of the International Maritime Organization (IMO) are getting stricter, and the demand for replacing the fuel of ships with eco-friendly fuels instead of heavy oil in the shipbuilding and marine industries is increasing. Among eco-friendly fuels, LNG (liquefied natural gas) is currently the most popular fuel. This is because it is an alternative that can avoid the IMO's environmental regulations by replacing fuel. In PART 1, as a basic study of laser welding of high manganese steel materials, a fiber laser bead-on-plate experiment was conducted using nitrogen protective gas, and the effect of each factor on the penetration shape was analyzed through cross-sectional observation. In PART II, argon and helium shielding gases, not the nitrogen shielding gas used in PART I, were tested under the same experimental conditions and the effect of the shielding gas on penetration during laser welding was conducted.
Abstract
Environmental regulations of the International Maritime Organization (IMO) are getting stricter, and the demand for replacing the fuel of ships with eco-friendly fuels instead of heavy oil in the shipbuilding and marine industries is increasing. Among eco-friendly fuels, LNG (liquefied natural gas) is currently the most popular fuel. This is because it is an alternative that can avoid the IMO's environmental regulations by replacing fuel. In PART 1, as a basic study of laser welding of high manganese steel materials, a fiber laser bead-on-plate experiment was conducted using nitrogen protective gas, and the effect of each factor on the penetration shape was analyzed through cross-sectional observation. In PART II, argon and helium shielding gases, not the nitrogen shielding gas used in PART I, were tested under the same experimental conditions and the effect of the shielding gas on penetration during laser welding was conducted.
참고문헌 (7)
- K. Li, "Determinants of ship operators’ options for compliance with IMO 2020", Transportation Research Part D: Transport and Environment, 86, pp.102459(1)~102459(17) (2020)
- 김재성, "GMAW 용접 시 보호가스 변화에 따른 TRIP 60 강재의 기계적 물성 특성", 대한용접접합학회지, 30(4), pp.304~308 (2012), 대한용접접합학회
- 안현준, "순 Ti GTA 용접부의 미세조직과 경도에 미치는 Ar-N2 보호가스 중 질소량의 영향", 대한용접접합학회지, 30(2), pp.169~173 (2012), 대한용접접합학회[DOI]
- 김철희, "후판 Al 5083 합금의 GMA 용접에서 보호가스 조성 및 용접변수에 따른 용접성의 평가", 대한용접접합학회지, 30(4), pp.294~299 (2012), 대한용접접합학회
- J. Chung, "The Low Temperature of Al5083-0 Welding Zone According to the Mixing Shield Gas Ratio", Journal of Welding and Joining, 20(6), pp.762~768 (2002)
- 안영남, "보호가스 종류에 따른 고출력 레이저 용접특성", 대한용접접합학회지, 33(4), pp.17~23 (2015), 대한용접접합학회
- 김종도, "강의 레이저-아크 하이브리드 용접시 공정변수에 따른 비드용접특성 (Ⅰ) - 보호가스 유량 및 레이저 아크간 거리의 영향 -", 대한용접접합학회지, 33(2), pp.85~90 (2015), 대한용접접합학회