비 직선 기어 홈 구조를 갖는 자동차용파킹기어의 금형 구조해석
Structural Analysis on Die of Parking Gear for Automotive withNonlinear Gear Groove
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
The parking gear is very important part of automotive because it is related to safety. Nonlinear gear groove of parking gear is used to enlarge the contact area between parking gear and pawl. The die has been widely applied for many industrial parts such as machine, automotive and so on. The purpose of this study is to investigate the stability of upper and lower dies by using numerical analysis. As the results, the lower die was weaker than the upper die in this study, and the lower die showed that it should be used within 500ton in terms of safety factor. Further the most weak point of lower die was low location in front of gear. Its minimum value of safety factor was 0.578 in case of 4000ton of press load, therefore, this weak point was needed to be reinforced.
Abstract
The parking gear is very important part of automotive because it is related to safety. Nonlinear gear groove of parking gear is used to enlarge the contact area between parking gear and pawl. The die has been widely applied for many industrial parts such as machine, automotive and so on. The purpose of this study is to investigate the stability of upper and lower dies by using numerical analysis. As the results, the lower die was weaker than the upper die in this study, and the lower die showed that it should be used within 500ton in terms of safety factor. Further the most weak point of lower die was low location in front of gear. Its minimum value of safety factor was 0.578 in case of 4000ton of press load, therefore, this weak point was needed to be reinforced.
참고문헌 (11)
- 손명규, "비 직선 기어 홈 구조를 갖는 자동차용 파킹기어의 열간단조 해석", 한국기계기술학회지, 21(1), pp.126~132 (2019), 한국기계기술학회[DOI]
- J. J. Park, "Research on Gear Manufacture by Cold Forging", Journal of the KSME, 33(3), pp.213~222 (1993)
- S. T. Won, "Trends of Press Forming Industry and Technology", The Korean Society for Technology of Plasticity, 23(6), pp.392~396 (2014)
- 박창현, "사출금형의 균일 냉각을 위한 냉각회로의 다중목적함수 최적설계", 한국자동차공학회 논문집, 20(1), pp.124~130 (2012), 한국자동차공학회
- 강경훈, "형상최적화 기법을 이용한 초고강도강판 성형용 프레스 금형의 구조설계 가이드라인", 소성∙가공, 26(6), pp.372~377 (2017), 한국소성∙가공학회[DOI]
- 정준태, "플라스틱 유동을 고려한 사출성형 충전공정 중 금형의 변형 해석", 대한기계학회논문집 A, 38(7), pp.719~725 (2014), 대한기계학회
- M. S. Joun, "A Structural Analysis System for Forging Die Sets Design, AFDEX", DIE, 2000, pp.9(2), 165~170
- 송민재, "금형 변형을 고려한 자동차 펜더패널의 성형해석", 소성∙가공, 15(5), pp.387~394 (2006), 한국소성∙가공학회
- 김세호, "전단-구조연계해석을 이용한 섀시부품 전단금형의 형상설계", 소성∙가공, 31(5), pp.261~266 (2022), 한국소성∙가공학회[DOI]
- 손명규, "자동차 파킹기어와 멈춤쇠의 접촉위치에 따른안정성 연구", 한국기계기술학회지, 23(3), pp.378~384 (2021), 한국기계기술학회[DOI]
- S. G. Yoon, "Autotech Textbook" (2020)