이종 강화재를 첨가한 폴리우레탄 폼의 기계적 및 열적 특성과 제작 시 초음파 분산의 영향
Mechanical and Thermal Characteristics of Polyurethane Foam with Two Different Reinforcements and the Effects of Ultrasonic Dispersion in Manufacturing
2
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
Since Liquefied Natural Gas (LNG) is normally carried at 1.1 bar pressure and at -163℃, special Cargo Containment System (CCS) are used. As LNG carrier is becoming larger, typical LNG insulation systems adopt a method to increase the thickness of insulation panel to reduce sloshing load and Boil-off Rate (BOR). However, this will decrease LNG cargo volume and increase insulation material costs. In this paper, silica aerogel, glass bubble were synthesized in polyurethane foam to increase volumetric efficiency by improving mechanical and thermal performance of insulation. In order to increase dispersibility of particles, ultrasonic dispersion was used. Dynamic impact test, quasi-static compression test at room temperature (20℃) and cryogenic temperature (-163℃) was evaluated. To evaluate the thermal performance, the thermal conductivity at room temperature (20℃) was measured. As a result, specimens without ultrasonic dispersion have a little effect on strength under the compressive load, although they show high mechanical performance under the impact load. In contrast, specimens with ultrasonic dispersion have significantly increased impact strength and compressive strength. Recently, as the density of Polyurethane foam (PUF) has been increasing, these results can be a method for improving the mechanical and thermal performance of insulation panel.
Abstract
Since Liquefied Natural Gas (LNG) is normally carried at 1.1 bar pressure and at -163℃, special Cargo Containment System (CCS) are used. As LNG carrier is becoming larger, typical LNG insulation systems adopt a method to increase the thickness of insulation panel to reduce sloshing load and Boil-off Rate (BOR). However, this will decrease LNG cargo volume and increase insulation material costs. In this paper, silica aerogel, glass bubble were synthesized in polyurethane foam to increase volumetric efficiency by improving mechanical and thermal performance of insulation. In order to increase dispersibility of particles, ultrasonic dispersion was used. Dynamic impact test, quasi-static compression test at room temperature (20℃) and cryogenic temperature (-163℃) was evaluated. To evaluate the thermal performance, the thermal conductivity at room temperature (20℃) was measured. As a result, specimens without ultrasonic dispersion have a little effect on strength under the compressive load, although they show high mechanical performance under the impact load. In contrast, specimens with ultrasonic dispersion have significantly increased impact strength and compressive strength. Recently, as the density of Polyurethane foam (PUF) has been increasing, these results can be a method for improving the mechanical and thermal performance of insulation panel.
참고문헌 (12)
- 안재혁, "글라스버블", 폴리우레탄 폼 복합재료의 기계적 및 열적 특성평가, 2018, pp.42(9), 708~714[DOI]
- 안재혁, "실리카 에어로겔을 첨가한 폴리머 폼의 기계적 특성", 한국해양공학회지, 31(6), pp.413~418 (2017), 한국해양공학회[DOI]
- 배진호, "글라스버블", 에폭시 수지 접착부의 극저온 압축 동적 성능, 2019, pp.32(2), 90~95[DOI]
- Blumm, J., "Handbook of Measurement in Science and Engineering", pp.1151~1188 (2012)
- Choi, S. W., "Analysis of two main LNG CCS(cargo containment system)insulation boxes for leakage safety using experimentally defined thermal properties", Applied Ocean Research, 37, pp.72~89 (2012)
- "Mark III High Density (HD) Foam" (2015)[URL]
- Goods, S. H., "Mechanical properties of a particle‐strengthened polyurethane foam", Journal of Applied Polymer Science, 74(11), pp.2724~2736 (1999)
- Youn Hee Kim, "Effects of Organoclay on the Thermal Insulating Properties of Rigid Polyurethane Foams Blown by Environmentally Friendly Blowing Agents", Macromolecular Research, 15(7), pp.676~681 (2007), 한국고분자학회
- Lee, Y., "Development of mass production type rigid polyurethane foam for LNG carrier using ozone depletion free blowing agent", Cryogenics, 80, pp.44~51 (2016)
- McGee, S. D., "Predicting the effect of temperature on the shock absorption properties of polyethylene foam", Packaging Technology and Science, 30(8), pp.477~494 (2017)
- Nazeran, N., "Synthesis and characterization of silica aerogel reinforced rigid polyurethane foam for thermal insulation application", Journal of Non-Crystalline Solids, 461(1), pp.1~1 (2017)
- Tseng, C. J., "Thermal conductivity of polyurethane foams from room temperature to 20 K", Cryogenics, 37(6), pp.305~312 (1997)