LNG 화물창 정밀 구조해석을 위한 에폭시와 폴리우레탄 접착제 기계적 물성치 분석
Mechanical Properties Analysis of Epoxy and Polyurethane Adhesive for Accurate Structural Analysis of LNG Cargo Hold
2
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
As the demand for natural gas that satisfies environmental regulations increases, the quantities of natural gas cargo that carrier can load is also increasing. Natural gas is transported in a liquefied state at -163 ℃ to increase loading efficiency. Among several LNG CCS types, MARK-III types are generally adopted in terms of loading efficiency. The secondary barrier adhesives of the MARK-III, nevertheless, is subjected to tensile stress due to thermal contraction and tension in the environment. In terms of these reasons, local analysis of the adhesive to evaluate the stress state must be carried out. According to previous studies, local analysis is unavailable since material properties for secondary barrier adhesives have not been reported. Thus, in this study, the cryogenic tensile test and coefficient of thermal expansion of epoxy and polyurethane (PU15, PU45), which are most widely used at cryogenic temperatures, were experimentally analyzed. At cryogenic temperature, the mechanical behavior of the polyurethane adhesive was better than epoxy of the adhesive. the joint of FSB and epoxy adhesive of the secondary barrier has the maximum coefficient of thermal expansion difference at 25 ℃ and minimum at –150 ℃, respectively.
Abstract
As the demand for natural gas that satisfies environmental regulations increases, the quantities of natural gas cargo that carrier can load is also increasing. Natural gas is transported in a liquefied state at -163 ℃ to increase loading efficiency. Among several LNG CCS types, MARK-III types are generally adopted in terms of loading efficiency. The secondary barrier adhesives of the MARK-III, nevertheless, is subjected to tensile stress due to thermal contraction and tension in the environment. In terms of these reasons, local analysis of the adhesive to evaluate the stress state must be carried out. According to previous studies, local analysis is unavailable since material properties for secondary barrier adhesives have not been reported. Thus, in this study, the cryogenic tensile test and coefficient of thermal expansion of epoxy and polyurethane (PU15, PU45), which are most widely used at cryogenic temperatures, were experimentally analyzed. At cryogenic temperature, the mechanical behavior of the polyurethane adhesive was better than epoxy of the adhesive. the joint of FSB and epoxy adhesive of the secondary barrier has the maximum coefficient of thermal expansion difference at 25 ℃ and minimum at –150 ℃, respectively.
참고문헌 (12)
- Albedah, A, "Effects of adhesive disbond and thermal residual stresses on the fatigue life of cracked 2024-T3 aluminum panels repaired with a composite patch", International Journal of Adhesion and Adhesives, 87, pp.22~30 (2018)
- Bang, C. S., "Performance improvement by glass fiber of adhesively bonded metal joints at the cryogenic temperature", Composite Structures, 96, pp.321~331 (2013)
- Galvez, P, "Effect of moisture and temperature on thermal and mechanical properties of structural polyurethane adhesive joints", Composite Structures, pp.112443~ (2020)
- 정연제, "멤브레인 형 2차 방벽 이방성 복합재료의 섬유방향에 따른 기계적 성능 평가", 대한조선학회 논문집, 57(3), pp.168~174 (2020), 대한조선학회[DOI]
- Oh, D. J, "Reliability evaluation of a LNGC insulation system with a metallic secondary barrier", Composite Structures, 171, pp.43~52 (2017)
- Petrie, E. M, "Handbook of adhesives and sealants" (2000), McGraw-Hill Education
- Surendra, K. M, "Mechanical behavior of glass", epoxy composites at liquid nitrogen temperature, 2008, pp.27(9), 937~944
- Wang, Y, "Effect of the temperature and strain rate on the tension response of uncured rubber : experiments and modeling", Mechanics of Materials, pp.103480~ (2020)
- Yoon, S. H, "Cryogenic strength of adhesive bridge joints for thermal insulation sandwich constructions", Composite Structures, 111, pp.1~12 (2014)
- Yu, Y. H, "Cryogenic characteristics of chopped glass fiber reinforced polyurethane foam", Composite Structures, 107, pp.476~481 (2014)
- Yoon, S. H, "Improvement of the adhesive peel strength of the secondary barrier with level difference for LNG containment system", Composite Structures, 95, pp.528~538 (2013)
- Zhang, Y. Y, "Mechanical properties of graphynes under tension: a molecular dynamics study", Applied Physics Letters, 101(8), pp.081909~ (2012)