Analysis on Stitched Mode I Specimen Using Spring Elements
1
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
Several studies related to reinforce composites structures in the through thickness direction have been developed along the years. As follows, in this study a new reinforced process is proposed based on previous experimental results using a novel stitching process in T-joints and one-stitched specimens. It was established the need to perform more analysis under standard test methods to obtain a better understanding. FEM analysis were compared after performed mode I interlaminar fracture toughness test, using different stitching patterns to analyze the through thickness strength with reference laminates without stitching. The stitching patterns were defined in 2x2 and 3x3, where the upper and lower head of the non- continuous stitching process (I-Fiber) has proven to influence in a higher through thickness strength of the laminate. In order to design the numerical model, cohesive parameters were required to define the surface to surface bonding elements using the cohesive zone method (CZM) and simulate the crack opening behavior from the double cantilever beam (DCB) test.
Abstract
Several studies related to reinforce composites structures in the through thickness direction have been developed along the years. As follows, in this study a new reinforced process is proposed based on previous experimental results using a novel stitching process in T-joints and one-stitched specimens. It was established the need to perform more analysis under standard test methods to obtain a better understanding. FEM analysis were compared after performed mode I interlaminar fracture toughness test, using different stitching patterns to analyze the through thickness strength with reference laminates without stitching. The stitching patterns were defined in 2x2 and 3x3, where the upper and lower head of the non- continuous stitching process (I-Fiber) has proven to influence in a higher through thickness strength of the laminate. In order to design the numerical model, cohesive parameters were required to define the surface to surface bonding elements using the cohesive zone method (CZM) and simulate the crack opening behavior from the double cantilever beam (DCB) test.
참고문헌 (20)
- Ji, H., "Fatigue Characteristics of Stainless Steel Pin-reinforced Composite Hat Joints", Composite Structures, 108, pp.49~56 (2014)
- Jones, R. M., "Mechanics of Composite Materials" (1999), Taylor & Framcis Inc
- Mouritz, A. P., "Review of Applications for Advanced Three-dimensional Fibre Textile Composites", Composites Part A, 30, pp.1445~1461 (1999)
- Ayranci, C., "2D Braided Composites : A Review for Stiffness Critical Applications", Composite Structures, 85, pp.43~58 (2008)
- Chou, S., "The Weaving Methods of Threedimensional Fabrics of Advanced Composite Materials", Composite Structures, 33, pp.159~172 (1995)
- Chi, H., "Bridging Micromechanisms of z-pin in Mixed Mode Delamination", Composite Structures, 93, pp.2685~2695 (2011)
- Ko, F. K, "Three-dimensional Fabrics for Composites, Composite Materials Series" (1989), Elsevier Science
- Grassi, M., "Finite Element Analyses of Mode I Interlaminar Delamination in z-fibre Reinforced Composite Laminates", Journal of Composites Science and Technology, 63(12), pp.1815~1832 (2003)
- 강민송, "변형률 에너지 해방률에 기반한 Carbon", Epoxy 직교적층판의 모드 I 층간 및 층내 파괴 특성 분석, 2019, pp.32(1), 6~12[DOI]
- Bianchi, F., "Numerical Modelling of Through-Thickness Reinforced Structural Joints", PhD, pp.2012
- Kim, C. H., "Failure Strength of Composite T-joint Prepared Using a New 1-thread Stitching Process", Composite Structures, 178, pp.225~231 (2017)
- Song, M. C., "Analysis of Mode I Delamination of z-pinned Composites Using a Nondimensional Analytical Model", Composites Part B, 43, pp.1776~1784 (2012)
- "Torayca T300 Technical Data Sheet No. CFA-001", ~
- Alfano, G., "Finite Element Interface Models for the Delamination Analysis of Laminated Composites : Mechanical and Computational Issues", International Journal for Numerical Methods in Engineering, 50, pp.1701~1736 (2001)
- Yan, Y., "Cohesive Zone Modeling of Interfacial Delamination in PZT Thin Films", International Journal of Solids and Structures, 46, pp.2739~2749 (2009)
- Diehl, T., "On Using a Penalty-based Cohesive-zone Finite Element Approach, Part II : Inelastic Peeling if an Epoxy-bonded Aluminium Strip", International Journal of Adhesion and Adhesives, 28, pp.256~265 (2008)
- "ANSYS Documentation, Mechanical APDL" (2018), ANSYS Inc
- Kravchenko, S., "Composite Toughness Enhancement with Interlaminar Reinforcement", Composites Part A, 54, pp.98~106 (2013)
- Bianchi, F., "A Cohesive Zone Model for Predicting Delamination Suppression on z-pinned Laminates", Composites Science and Technology, 71, pp.1898~1907 (2011)
- Mohamed, G., "Cohesive Element Formulation for z-pin Delamination Bridging in Fibre Reinforced Laminates", International Journal of Solids and Structures, 132-133, pp.232~244 (2017)