Study on the Vibration Characteristics of Yaw Gear System for Large-Capacity Offshore Wind Turbine
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Vibration and noise must be considered to maximize the efficiency of a yaw system and reduce the fatigue load acting on a wind turbine. This study investigated a method for analyzing yaw-system vibration based on the change in the load-duration distribution (LDD). A substructure synthesis method was combined with a planetary gear train rotational vibration model and finite element models of the housing and carriers. For the vibration excitation sources, the mass imbalance, gear mesh frequency, and bearing defect frequency were considered, and a critical speed analysis was performed. The analysis results showed that the critical speed did not occur within the operating speed range, but a defect occurred in the bearing of the first-stage planetary gear system. It was found that the bearing stiffness and first natural frequency increased with the LDD load. In addition, no vibration occurred in the operating speed range under any of the LDD loads. Because the rolling bearing stiffness changed with the LDD, it was necessary to consider the LDD when analyzing the wind turbine vibration.
Abstract
Vibration and noise must be considered to maximize the efficiency of a yaw system and reduce the fatigue load acting on a wind turbine. This study investigated a method for analyzing yaw-system vibration based on the change in the load-duration distribution (LDD). A substructure synthesis method was combined with a planetary gear train rotational vibration model and finite element models of the housing and carriers. For the vibration excitation sources, the mass imbalance, gear mesh frequency, and bearing defect frequency were considered, and a critical speed analysis was performed. The analysis results showed that the critical speed did not occur within the operating speed range, but a defect occurred in the bearing of the first-stage planetary gear system. It was found that the bearing stiffness and first natural frequency increased with the LDD load. In addition, no vibration occurred in the operating speed range under any of the LDD loads. Because the rolling bearing stiffness changed with the LDD, it was necessary to consider the LDD when analyzing the wind turbine vibration.
참고문헌 (16)
- Bossanyi, E. A., "Further load reductions with individual pitch control", Wind Energy, 8(4), pp.481~485 (2005)[DOI]
- Choi, J. W., "A review of mode synthesis techniques and its application between FE and experimental Model", Transactions of the Korean Society of Mechanical Engineers, 13, pp.799~806 (1989)[DOI]
- Choy, F. K., "Vibration signature and modal analysis of multi-stage gear transmission", Journal of the Franklin Institute, 328(2), pp.281~298 (1991)[DOI]
- Dong, H., "Dynamic modeling of planetary gear train for vibration characteristic analysis", Mechanisms Trasmissions and Application, 31, pp.187~195 (2015)[DOI]
- Hong, H. S., "Research for 2MW wind turbine tower shell design optimization", The Korean Society for New and Renewable Energy, 2(4), pp.19~26 (2006)
- Iida, H., "Coupled torsional-flexural vibration of a shaft in a geared system of rotors", Bulletin of JSME, 23(186), pp.2111~2117 (1980)[DOI]
- Itoh, T., "Damped vibration mode superposition method for dynamic response anaylsis", Earthquake Engineering Structural Dynamics, 2(1), pp.47~57 (1973)[DOI]
- Kahraman, A., "Dynamic analysis of geared rotors by finite elements", Journal of Mechanical Design, 114(3), pp.507~514 (1992)[DOI]
- 김정수, "풍력발전시스템의 진동특성", 한국마린엔지니어링학회지, 35(6), pp.786~795 (2011), 한국마린엔지니어링학회
- Lee, H. Y., "An analytical investigation on vibrational characteristics of multi-mesh geared system using transfer aatrix method", Master’s, pp.1999
- 이형우, "2.5MW 풍력발전기 기어박스 치형수정", 한국생산제조학회지, 23(2), pp.109~117 (2014), 한국생산제조학회[DOI]
- 민영실, "2MW급 풍력발전기 사이클로이드 피치감속기 설계에 대한 연구", 한국마린엔지니어링학회지, 39(9), pp.895~902 (2015), 한국마린엔지니어링학회[DOI]
- Parker, R. G., "Dynamic response of a planetary gear system using a finite element", contact mechanics model, 2000, pp.122(3), 304~310
- Prohl, M. A., "A general method for calculating critical speeds of flexible rotors", Journal of Applied Mechanics, 12(3), pp.142~148 (1945)[DOI]
- Tanata, M., "Matrix methods in planetary gear train analyses", Society of Automotive Engineers, 93(5), pp.333~340 (1984)[DOI]
- Wang, S. M., "Torsional response of a gear train system", Manfacturing Science and Engineering, 94(2), pp.583~592 (1972)[DOI]