Fe-Si 전기강판 폐스크랩을 이용한 연자성 분말 및 테이프 제조기술
Manufacturing Technology for Tape Casting and Soft Magnetic Powder Using by Recycling Scrap of Fe-Si Electrical Sheet
2
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
This study focused on examining the possibility for recycling of Fe-Si electric sheet. We manufactured Fe- 6.5Si mother alloy using by Fe-Si electric sheet scrap for transformer core materials. And then, soft magnetic alloy powder which diameter and shape were 45~150 μm and sphere type was prepared by gas atomization process. As we compared to commercial Fe-6.5Si powder, its diameter distribution and microstructure of recycled powder was a similar. To investigate the possibility of reusing the soft magnetic composite sheet for electronics, recycled powder was treated to have a high aspect ratio (AR), and we finally obtained the 65~66 AR and 2.3 μm thickness powder. To release the residual stress of powder, heat treatment was conducted under 300~400oC, N2 gas. And then, soft magnetic sheet was made by tape casting process using by those powders. After the density and permeability of tape was measured, and we confirmed that the recycled Fe-Si electric sheet scrap was possible to reuse the soft magnetic materials of electronics.
Abstract
This study focused on examining the possibility for recycling of Fe-Si electric sheet. We manufactured Fe- 6.5Si mother alloy using by Fe-Si electric sheet scrap for transformer core materials. And then, soft magnetic alloy powder which diameter and shape were 45~150 μm and sphere type was prepared by gas atomization process. As we compared to commercial Fe-6.5Si powder, its diameter distribution and microstructure of recycled powder was a similar. To investigate the possibility of reusing the soft magnetic composite sheet for electronics, recycled powder was treated to have a high aspect ratio (AR), and we finally obtained the 65~66 AR and 2.3 μm thickness powder. To release the residual stress of powder, heat treatment was conducted under 300~400oC, N2 gas. And then, soft magnetic sheet was made by tape casting process using by those powders. After the density and permeability of tape was measured, and we confirmed that the recycled Fe-Si electric sheet scrap was possible to reuse the soft magnetic materials of electronics.
참고문헌 (18)
- 서일웅, "IGBT 전력반도체 모듈 패키지의 방열 기술", 마이크로전자 및 패키징학회지, 21(3), pp.7~17 (2014), 한국마이크로전자및패키징학회[DOI]
- Potential Value Evaluation of The Rare Metal in Urban mine, "H. S. Jung", Samsung Economic Research Institute, ~ (2011)
- J. P. Hong, "The Electric Equipment and Magnetic Materials", The Transac. Korean Ins. Electric. Eng, 55(9), pp.45~ (2006)
- C. J. Yang, "The Tehcnology Development Trend of Magnetic Materials", J. Korean Inst. Electr. Electron. Mater. Eng, 13(11), pp.1~ (2000)
- Y. D. Shin, "Research Trend and Development of Hard Magnetic Materials", J. Korean Inst. Electr. Electron. Mater. Eng, 9(1), pp.93~ (1996)
- 최판규, "일본의 원소전략 프로젝트", 한국자기학회지, 24(6), pp.197~201 (2014), 한국자기학회
- Y. Hirayama, , Scripta Materialia, 95, pp.70~ (2015)
- S. Suzuki, , AIP Advaces, 4, pp.117131~ (2014)
- 김종렬, "나노 연", 경자성 분말 재료를 이용한 Exchange-coupling 자석의 제조 기술, 2011, pp.21(6), 225~230[DOI]
- E. F. Kneller, "The exchange-spring magnet:a new material principle for permanent magnets", IEEE Trans. Magn, 27, pp.3588~ (1991)
- 이충효, "기계적합금화에 의한 Fe2O3-Mg계 연자성 콤포지트의 합성 및 평가", 한국결정성장학회지, 25(6), pp.245~251 (2015), 한국결정성장학회[DOI]
- C. C. Koch, "Preparation of amorphous Ni60Nb40 by mechanical alloying", Appl. Phys. Lett, 43, pp.1017~ (1983)
- H. J. Fecht, "Nanocrystalline metals prepared by high-energy ball milling", Metal. Trans, 21, pp.2333~ (1990)
- J. Eckert, "Glass formation and extended solubilities in mechanically alloyed cobalt-transition metal alloys", J. Less-Common Metals, 166, pp.293~ (1990)
- U. Mizutani, "Effect of mechanical alloying beyond the completion of glass formation for Ni-Zr alloy powders", J. Mater. Sci, 25, pp.399~ (1990)
- K. Suzuki, "Structural characterization of Ni-V amorphous alloys prepared by mechanical alloying", Mater. Sci. Eng., A, 134, pp.987~ (1991)
- R. B. Schwarz, "Formation of an amorphous alloy by solid state reaction of the pure polycrystalline metals", Phys. Rev. Lett, 51, pp.415~ (1983)
- 이중근, "Dual band Antenna Switch Module의 LTCC 공정변수에 따른 안정성 및 특성 개선에 관한 연구", 마이크로전자 및 패키징학회지, 12(2), pp.105~109 (2005), 한국마이크로전자및패키징학회