Anodic Oxidation Behavior of AZ31 Magnesium Alloy in Aqueous Electrolyte Containing Various Na2CO3 Concentrations
2
조회
0
다운로드
9
인용
0
참고문헌
키워드
초록
In this work, anodic oxidation behavior of AZ31 Mg alloy was studied as a function of Na2CO3 concentration in electrolyte by voltage-time curves and observation of surface appearances and morphologies after the anodic treatments, using optical microscopy and confocal scanning laser microscopy (CSLM). The voltage-time curves of AZ31 Mg alloy surface and surface appearances after the anodic treatments showed three different regions with Na2CO3 concentration : region I, below 0.2 M Na2CO3 where shiny surface with a number of small size pits; region II, between 0.4 M and 0.6 M Na2CO3 where dark surface with relatively low number of large size burned or dark spots; region III, more than 0.8 M Na2CO3 where bright surface with or without large size dark spots were obtained. The anodically treated AZ31 Mg alloy surface became significantly brightened with increasing Na2CO3 concentration from 0.5 M to 0.8 M which was attribute to the formation of denser and smoother surface films. Pits and porous protruding reaction products were found at relatively large size and small size spots, respectively, on the AZ31 Mg alloy surface in low concentration of Na2CO3 less than 0.2 M. The formation of pits is attributed to the result of repetition of the formation and detachment of porous anodic reaction products. Based on the experimental results obtained in this work, it is concluded that more uniform, denser and smoother surface of AZ31 Mg alloy could be obtained at more than 0.8 M Na2CO3 concentration if there is no other oxide forming agent.
Abstract
In this work, anodic oxidation behavior of AZ31 Mg alloy was studied as a function of Na2CO3 concentration in electrolyte by voltage-time curves and observation of surface appearances and morphologies after the anodic treatments, using optical microscopy and confocal scanning laser microscopy (CSLM). The voltage-time curves of AZ31 Mg alloy surface and surface appearances after the anodic treatments showed three different regions with Na2CO3 concentration : region I, below 0.2 M Na2CO3 where shiny surface with a number of small size pits; region II, between 0.4 M and 0.6 M Na2CO3 where dark surface with relatively low number of large size burned or dark spots; region III, more than 0.8 M Na2CO3 where bright surface with or without large size dark spots were obtained. The anodically treated AZ31 Mg alloy surface became significantly brightened with increasing Na2CO3 concentration from 0.5 M to 0.8 M which was attribute to the formation of denser and smoother surface films. Pits and porous protruding reaction products were found at relatively large size and small size spots, respectively, on the AZ31 Mg alloy surface in low concentration of Na2CO3 less than 0.2 M. The formation of pits is attributed to the result of repetition of the formation and detachment of porous anodic reaction products. Based on the experimental results obtained in this work, it is concluded that more uniform, denser and smoother surface of AZ31 Mg alloy could be obtained at more than 0.8 M Na2CO3 concentration if there is no other oxide forming agent.
참고문헌 (27)
- Nguyen Van Phuong, "The effects of surface pre-treatment methods on the structure and corrosion resistance of zinc phosphate conversion coatings on AZ31 Mg alloy", Science of Advanced Materials, 6, pp.1~7 (2014)
- Nguyen Van Phuong, "Comparative corrosion study of zinc phosphate and magnesium phosphate conversion coatings on AZ31 Mg alloy", Materials Letters, 122, pp.341~344 (2014)
- Nguyen Van Phuong, "Deposition and characterization of E-paint on magnesium alloys", Progress in Organic Coatings, 89, pp.91~99 (2015)
- Basit Raza Fazal, "Formation of Cerium Conversion Coatings on AZ31 Magnesium Alloy", 한국표면공학회지, 49(1), pp.1~13 (2016), 한국표면공학회[DOI]
- Nguyen Van Phuong, "Deposition and Characterization of Electrophoretic Paint on AZ31 Magnesium Alloy", 한국표면공학회지, 49(2), pp.141~146 (2016), 한국표면공학회[DOI]
- J. Liang, "Effect of potassium fluoride in electrolytic solution on the structure and properties of microarc oxidation coatings on magnesium alloy", Applied Surface Science, 252, pp.345~351 (2005)
- S. Verdier, "Formation, structure and composition of anodic films on AM60 magnesium alloy obtained by DC plasma anodising", Corros. Sci, 47, pp.1429~ (2005)
- H. Duan, "Effect of electrolyte additives on performance of plasma electrolytic oxidation films formed on magnesium alloy AZ91D", Electrochimica Acta, 52, pp.3785~3793 (2007)
- R. Arrabal, "Corrosion resistance of WE43 and AZ91D magnesium alloys with phosphate PEO coatings", Corrosion Science, 50, pp.1744~1752 (2008)
- L. Chai, "Anodizing of magnesium alloy AZ31 in alkaline solutions with silicate under continuous sparking", Corros. Sci, 50, pp.3274~ (2008)
- A. Yabuki, "Anodic films formed on magnesium in organic, silicate-containing electrolytes", Corros. Sci, 51, pp.793~ (2009)
- J. Liang, "Electrochemical corrosion behaviour of plasma electrolytic oxidation coatings on AM50magnesium alloy formed in silicate and phosphate based electrolytes", Electrochimica Acta, 54, pp.3842~3850 (2009)
- S. Moon, "Anodic oxidation of Mg-Sn alloys in alkaline solutions", Corrosion Science, 65, pp.494~501 (2012)
- S. Yagi, "Surface modification of ACM522 magnesium alloy by plasma electrolytic oxidation in phosphate electrolyte", Corrosion Science, 57, pp.74~80 (2012)
- T. S. Lim, "Electrochemical corrosion properties of CeO2-containing coatings on AZ31 magnesium alloys prepared by plasma electrolytic oxidation", Corros. Sci, 62, pp.104~ (2012)
- B. Kazanski, "Fluoride ions as modifiers of the oxide layer produced by plasma electrolytic oxidation on AZ91D magnesium alloy", Applied Surface Science, 287, pp.461~466 (2013)
- S. Moon, "Corrosion behavior of PEO-treated AZ31Mg alloy in chloride solution", Journal of Solid State Electrochemistry, 18, pp.341~346 (2014)
- 문성모, "AZ31 마그네슘 합금의 플라즈마전해산화 피막 형성에 미치는 수산화 이온 및 규산 이온의 영향", 한국표면공학회지, 47(4), pp.147~154 (2014), 한국표면공학회[DOI]
- G. Bian, "Effects of electrolytes on the growth behavior, microstructure and tribological properties of plasma electrolytic oxidation coatings on a ZA27alloy", Surface and Coatings Technology, 277, pp.251~257 (2015)
- Stojadinović, Stevan, "Characterization of plasma electrolytic oxidation of magnesium alloy AZ31 in alkaline solution containing fluoride", Surface and Coatings Technology, 273, pp.1~11 (2015)
- X. Lu, "Insights into plasma electrolytic oxidation treatment with particle addition", Corrosion Science, 101, pp.201~207 (2015)
- M. Mohedano, "Silicate-based Plasma Electrolytic Oxidation(PEO)coatings with incorporated CeO2 particles on AM50magnesium alloy", Materials & Design, 86, pp.735~744 (2015)
- X. Lu, "Plasma electrolytic oxidation coatings on Mg alloy with addition of SiO2 particles", Electrochimica Acta, 187, pp.20~33 (2016)
- S. Moon, "3-Dimensional structures of open-pores in PEO films on AZ31Mg alloy", Materials Letters, 161, pp.439~441 (2016)
- 권두영, "인산 및 규산 이온이 포함된 수용액에서 AZ31 마그네슘 합금의 플라즈마전해산화 피막의 구조에 미치는 수산화나트륨 농도의 영향", 한국표면공학회지, 49(1), pp.46~53 (2016), 한국표면공학회[DOI]
- 문성모, "Anodic Oxide Films Formed on AZ31 Magnesium Alloy by Plasma Electrolytic Oxidation Method in Electrolytes Containing Various NaF Concentrations", 한국표면공학회지, 49(3), pp.225~230 (2016), 한국표면공학회[DOI]
- 문성모, "A Blade-Abrading Method for Surface Pretreatment of Mg Alloys", 한국표면공학회지, 48(5), pp.194~198 (2015), 한국표면공학회[DOI]