모터링 엔진의 시동 사이클 및 시동 정지 사이클에서 저어널베어링의 마모 연구 – II. 해석 결과
Study on Wear of Journal Bearings during Start-up and Coast-down Cycles of a Motoring Engine – II. Analysis Results
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
In this paper, we present the results of the wear analysis of journal bearings on a stripped-down single-cylinder engine during start-up and coast-down by motoring. We calculate journal bearing wear by using a modified specific wear rate considering the fractional film defect coefficient and load-sharing ratio for the asperity portion of a mixed elastohydrodynamic lubrication (EHL) regime coupled with previously presented graphical data of experimental lifetime linear wear in radial journal bearings. Based on the calculated wear depth, we obtain a new oil film thickness for every crank angle. By examination of the oil film thickness, we determine whether the oil film thickness at the wear scar region is in a mixed lubrication regime by comparing dimensionless oil film thickness, h/σ, to 3.0 at every crank angle. We present the lift-off speed and the crank angles involved with the wear calculation for bearings #1 and #2. The dimensionless oil film thickness, h/σ, illustrates whether the lubrication region between the two surfaces is still within the bounds of the mixed lubrication regime after scarring of the surface by wear. In addition, we present in tables the asperity contact pressure, the real minimum film thickness at the wear scar region, the modified specific wear rate, and the wear angle, α, for bearings #1 & #2. To show the real shape of the oil film at wear scar region, we depict the actual oil film thickness in graphs. We also tabulated the ranges of bearing angles related with wear scar. We present the wear volume for bearings #1 and #2 after one turn-on and turn-off of the engine ignition switch for five kinds of equivalent surface roughness. We show that the accumulated wear volume after a single turn-on and turn-off of an ignition switch normally increases with increasing surface roughness, with a few exceptions.
Abstract
In this paper, we present the results of the wear analysis of journal bearings on a stripped-down single-cylinder engine during start-up and coast-down by motoring. We calculate journal bearing wear by using a modified specific wear rate considering the fractional film defect coefficient and load-sharing ratio for the asperity portion of a mixed elastohydrodynamic lubrication (EHL) regime coupled with previously presented graphical data of experimental lifetime linear wear in radial journal bearings. Based on the calculated wear depth, we obtain a new oil film thickness for every crank angle. By examination of the oil film thickness, we determine whether the oil film thickness at the wear scar region is in a mixed lubrication regime by comparing dimensionless oil film thickness, h/σ, to 3.0 at every crank angle. We present the lift-off speed and the crank angles involved with the wear calculation for bearings #1 and #2. The dimensionless oil film thickness, h/σ, illustrates whether the lubrication region between the two surfaces is still within the bounds of the mixed lubrication regime after scarring of the surface by wear. In addition, we present in tables the asperity contact pressure, the real minimum film thickness at the wear scar region, the modified specific wear rate, and the wear angle, α, for bearings #1 & #2. To show the real shape of the oil film at wear scar region, we depict the actual oil film thickness in graphs. We also tabulated the ranges of bearing angles related with wear scar. We present the wear volume for bearings #1 and #2 after one turn-on and turn-off of the engine ignition switch for five kinds of equivalent surface roughness. We show that the accumulated wear volume after a single turn-on and turn-off of an ignition switch normally increases with increasing surface roughness, with a few exceptions.
참고문헌 (24)
- Chun, S. M., "Parametric Study of Thermal and Unsteady Effects in Hydrodynamic Lubrication of Journal Bearings", 박사, pp.1989
- Fragoulis, A. H., "Instantaneous Frictional Torque of Reciprocating Combustion Engines", 박사, pp.1988
- Booker, J. F., "Dynamically Loaded Journal Bearings : Mobility Method of Solution", ASME J. Basic Engineering, 87, pp.537~546 (1965)
- Lu, X., "On the Lift-Off Speed in Journal Bearings", Tribol. Lett., 20(3), pp.299~305 (2005)[DOI]
- Chun S. M., "Parametric Study of Inlet Oil Temperature and Pressure for a Half-Circumferential Grooved Journal Bearing", Tribol. Trans, 35(2), pp.213~224 (1992)
- Chun S. M., "Aeration Effects on the Performance of a Turbocharger Journal Bearing", Tribol. Int, 41, pp.296~306 (2008)
- Patir, N., "An average Flow Model for Determining Effects of Three-Dimensional Roughness on Partial Hydrodynamic Lubrication", ASME J. Lubr. Technol, 100, pp.12~17 (1978)
- Majumdar, B. C., "Effect of Surface Roughness on Elaostohydrodynamic Line Contact", ASME J. Lubr. Technol., (104), pp.401~409 (1982)
- Khonsari, M. M., "Applied Tribology:Bearing Design and Lubrication" (2008), Wiley
- Chang, W. R., "An Elastic-Plastic Model for the Contact of Rough Surfaces", Trans. ASME, J. Tribol, 109, pp.257~263 (1987)
- Zhao, Y., "An Asperity Microcontact Model Incoporating the Transition from Elastic Deformation to Fully Plastic Flow", Trans. ASME, J. Tribol, 122, pp.86~93 (2000)
- Kogut, L., "A Finite Element based Elastic-Plastic Model for the Contact of Rough Surfaces", Tribol. Trans, 46, pp.383~390 (2003)
- Masjedi, M., "Film Thickness and Asperity Load Formulas for Line-Contact Elastohydrodynamic Lubrication with Provision for Surface Roughness", Trans. ASME, J. Tribol, 134(1), pp.011503~ (2012)
- Masjedi, M., "Theoretical and Experimental Investigation of Traction Coefficient in Line-contact EHL of Rough surfaces", Tribol. Int., 70, pp.179~189 (2014)[DOI]
- McCool, J. I., "Relating Profile Instrument Measurements to the Functional Performance of Rough Surfaces", Trans. ASME, J. Tribol., 109(2), pp.264~270 (1987)
- Kingsbury, E. P., "Some Aspect of the thermal desorption of a boundary lubricant", J. Appl. Phys, 29, pp.888~891 (1958)
- Rowe, C. N., "Some aspects of heat of adsorption in function of a boundary lubricant", ASLE Trans, 9, pp.101~111 (1966)
- Beheshti, A., "An Engineering Approach for the Prediction of Wear in Mixed Lubricated Contacts", Wear, 308, pp.121~131 (2013)[DOI]
- Beheshti, A., "Asperity Micro-contact Models as Applied to the Deformation of Rough Line Contact", Tribol. Int., 52, pp.61~74 (2012)[DOI]
- Hamrock, B. J., "Fundamentals of Fluid Film Lubrication" (1994), McGraw Hill
- Holm, R., "Electrical contacts" (1946), Almqvist & Wiksell
- Archard, J. F., "Contact and rubbing of flat surfaces", J. Appl. Phys, 24, pp.981~988 (1953)
- Chun, S. M., "Simulation of Engine Life Time Related with Abnormal Oil Consumption", Tribol. Int, 44, pp.426~436 (2011)
- Ligterink, D. J., "Measurements of Wear in Radial Journal Bearings", Tribotest Journal, 3(1), pp.45~54 (1996)