파이어링 시동 사이클 초기에서의 엔진 베어링 마모 시뮬레이션
Wear Simulation of Engine Bearings in the Beginning of Firing Start-up cycle
0
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
The purpose of this study is to estimate the wear volumes of engine journal bearings operating at variable angular velocity of a shaft in the beginning of firing start-up cycle. To do this, first we find the potential region of wear scar on engine journal bearings where the applied bearing load and crank shaft velocity are variable. The potential wear regions are discovered by finding minimum oil film thickness at every crank angle existing below most oil film thickness scaring wear (MOFTSW) obtained based on the concept of the centerline average surface roughness. Then we calculate the wear volume from the wear depth and two wear angles decided by the magnitude of each film thickness lower than MOFTSW at every crank angle. The results show that the expected wear region is located at a few bearing angles after and/or behind the upper center of a big-end bearing and the lower center of a main bearing. And the real wear region is similar to the estimated wear region. Further we find that the wear scar on an engine journal bearing may occur at re-starting time after switch-off of a start motor especially under the condition of high oil temperature.
Abstract
The purpose of this study is to estimate the wear volumes of engine journal bearings operating at variable angular velocity of a shaft in the beginning of firing start-up cycle. To do this, first we find the potential region of wear scar on engine journal bearings where the applied bearing load and crank shaft velocity are variable. The potential wear regions are discovered by finding minimum oil film thickness at every crank angle existing below most oil film thickness scaring wear (MOFTSW) obtained based on the concept of the centerline average surface roughness. Then we calculate the wear volume from the wear depth and two wear angles decided by the magnitude of each film thickness lower than MOFTSW at every crank angle. The results show that the expected wear region is located at a few bearing angles after and/or behind the upper center of a big-end bearing and the lower center of a main bearing. And the real wear region is similar to the estimated wear region. Further we find that the wear scar on an engine journal bearing may occur at re-starting time after switch-off of a start motor especially under the condition of high oil temperature.
참고문헌 (24)
- Chun, S. M., "Wear simulation for the journal bearings operating under aligned shaft and steady load during start-up and coast-down conditions", Tribology International, 97, pp.440~466 (2016)[DOI]
- 전상명, "모터링 시동 및 시동정지 사이클에서 경사진 축을 갖는 저어널베어링의 마모 해석 – Part I: 마모발생 가능영역에서의 유막 변화 연구", 한국트라이볼로지학회지, 33(4), pp.153~167 (2017), 한국트라이볼로지학회[DOI]
- 전상명, "모터링 시동 및 시동정지 사이클에서 경사진 축을 갖는 저어널베어링의 마모 해석 - Part II: 경사진 축을 지지하는 두 저어널베어링의 마모해석", 한국트라이볼로지학회지, 33(4), pp.168~186 (2017), 한국트라이볼로지학회[DOI]
- 전상명, "파이어링 상태의 일정 축 각속도에서 엔진 베어링의 마모 해석 – Part I: 베어링 마모발생 부위 파악", 한국트라이볼로지학회지, 34(3), pp.93~106 (2018), 한국트라이볼로지학회[DOI]
- 전상명, "파이어링 상태의 일정 축 각속도에서 엔진베어링의 마모 해석− Part II: 저어널베어링 마모 계산", 한국트라이볼로지학회지, 34(4), pp.146~159 (2018), 한국트라이볼로지학회[DOI]
- Chun, S. M., "Parametric Study of Thermal and Unsteady Effects in Hydrodynamic Lubrication of Journal Bearings", Ph. D, pp.1989
- Booker, J. F., "Dynamically-Loaded Journal Bearings:Mobility Method of Solution", Trans. Of the ASME, J. of Basic Engineering, 87, pp.537~546 (1965)
- Booker, J. F., "Dynamically-Loaded Journal Bearings:Numerical Application of the Mobility Method", Trans. of the ASME, J. of Lubrication Technology, 93(1), pp.168~176 (1971)
- X. Lu, "On the Lift-off Speed in Journal Bearings", Tribology Letters, 20(3-4), pp.299~305 (2005), Springer Science and Business Media LLC[DOI]
- Chun S. M., "Parametric Study of Inlet Oil Temperature and Pressure for a Half-Circumferential Grooved Journal Bearing", Tribol. Trans., 35(2), pp.213~224 (1992)
- Sang Myung Chun, "Aeration effects on the performance of a turbocharger journal bearing", Tribology International, 41(4), pp.296~306 (2008), Elsevier BV[DOI]
- Ligterink, D. J., "Measurements of Wear in Radial Journal Bearings", Tribotest Journal, 3(1), pp.45~54
- Zhao, Y., "An Asperity Microcontact Model Incoporating the Transition from Elastic Deformation to Fully Plastic Flow", Trans. ASME, J. Tribol., 122, pp.86~93 (2000)
- Masjedi, M., "Film Thickness and Asperity Load Formulas for Line-Contact Elastohydrodynamic Lubrication with Provision for Surface Roughness", Trans. ASME, J. Tribol., 134(1), pp.011503~ (2012)[DOI]
- McCool, J. I., "Relating Profile Instrument Measure-ments to the Functional Performance of Rough Surfaces", Trans. ASME, J. Tribol., 109(2), pp.264~270 (1987)
- Kingsbury, E. P., "Some Aspect of the thermal desorption of a boundary lubricant", J. Appl. Phys, 29, pp.888~891 (1958)
- Rowe, C. N., "Some aspects of heat of adsorption in function of a boundary lubricant", ASLE Trans., 9, pp.101~111 (1966)
- Holm, R., "Electrical contacts" (1946), Almqvist & Wiksell
- Archard, J. F., "Contact and rubbing of flat surfaces", J. Appl. Phys., 24, pp.981~988 (1953)
- Kogut, L., "Elastic-Plastic Contact Analysis of a Sphere and a Rigid Flat", Trans. ASME, J. Applied Mechanics, 69, pp.657~662 (2002)
- Kogut, L., "A Finite Element based Elastic-Plastic Model for the Contact of Rough Surfaces", Tribol. Trans., 46, pp.383~390 (2003)
- Ali Beheshti, "Asperity micro-contact models as applied to the deformation of rough line contact", Tribology International, 52, pp.61~74 (2012), Elsevier BV[DOI]
- Patir, N., "An average Flow Model for Determining Effects of Three-Dimensional Roughness on Partial Hydrodynamic Lubrication", ASME J. Lubr. Technol, 100, pp.12~17 (1978)
- 전상명, "딥스틱게이지형 소형 엔진오일열화감지센서의 시험결과 분석", 한국트라이볼로지학회지, 30(3), pp.156~167 (2014), 한국트라이볼로지학회[DOI]