모터링 시동 및 시동정지 사이클에서 경사진 축을 갖는 저어널베어링의 마모 해석 - Part II: 경사진 축을 지지하는 두 저어널베어링의 마모해석
Wear Analysis of Journal Bearings Operating in a Shaft During Motoring Start-up and Coast-down Cycles – Part II: Wear Analysis of two Journal Bearings Supporting a Misaligned Shaft
0
조회
0
다운로드
5
인용
0
참고문헌
키워드
초록
This paper presents a wear analysis procedure for calculating the wear of journal bearings during the start-up and coast-down cycles of a motoring stripped-down single cylinder engine operating with a tilted shaft. In order to decide whether the lubrication state of a journal bearing is in the mixed-elasto-hydrodynamic lubrication regime, we utilize lift-off speed and MOFT (most oil film thickness) under mixed-elasto-hydrodynamic lubrication regime at the corresponding aligned shaft. We formulate an equation for the modified film thickness in a misaligned journal bearing considering the additional wear volume described in Part I of this study. For this, we use the calculation results of the degree of misalignment and tilting angle obtained after finding the eccentricities of the two bearings supporting the crankshaft of a single cylinder engine. In this Part II, we calculate the wear of journal bearings using the fractional film defect coefficient, the asperity load sharing factor, and the modified specific wear rate for the application of mixed-elasto-hydrodynamic lubrication regime. We show that the accumulated wear volume after turning the ignition switch on and off once, increases to σ = 39 μm and then decreases from σ = 39 μm with increasing in surface roughness.
Abstract
This paper presents a wear analysis procedure for calculating the wear of journal bearings during the start-up and coast-down cycles of a motoring stripped-down single cylinder engine operating with a tilted shaft. In order to decide whether the lubrication state of a journal bearing is in the mixed-elasto-hydrodynamic lubrication regime, we utilize lift-off speed and MOFT (most oil film thickness) under mixed-elasto-hydrodynamic lubrication regime at the corresponding aligned shaft. We formulate an equation for the modified film thickness in a misaligned journal bearing considering the additional wear volume described in Part I of this study. For this, we use the calculation results of the degree of misalignment and tilting angle obtained after finding the eccentricities of the two bearings supporting the crankshaft of a single cylinder engine. In this Part II, we calculate the wear of journal bearings using the fractional film defect coefficient, the asperity load sharing factor, and the modified specific wear rate for the application of mixed-elasto-hydrodynamic lubrication regime. We show that the accumulated wear volume after turning the ignition switch on and off once, increases to σ = 39 μm and then decreases from σ = 39 μm with increasing in surface roughness.
참고문헌 (36)
- 전상명, "모터링 시동 및 시동정지 사이클에서 경사진 축을 갖는 저어널베어링의 마모 해석 – Part I: 마모발생 가능영역에서의 유막 변화 연구", 한국윤활학회지, 33(4), pp.153~167 (2017), 한국윤활학회[DOI]
- Sang Myung Chun, "Wear simulation for the journal bearings operating under aligned shaft and steady load during start-up and coast-down conditions", Tribology International, 97, pp.440~466 (2016), Elsevier BV[DOI]
- Chun, S. M., "Parametric Study of Thermal and Unsteady Effects in Hydrodynamic Lubrication of Journal Bearings", Ph. D., pp.1989
- Fragoulis, A. H., "Instantaneous Frictional Torque of Reciprocating Combustion Engines", Ph. D., pp.1988
- Booker, J. F., "Dynamically-loaded journal bearings:mobility method of solution", Trans. Of the ASME, J. Basic Engineering, 87, pp.537~546 (1965)
- Booker, J. F., "Dynamically-Loaded Journal Bearings:Numerical application of the mobility method", Trans. of the ASME, J. Lubrication Technology, 93(1), pp.168~176 (1971)
- Patir, N., "An average flow model for determining effects of Three-Dimensional roughness on partial hydrodynamic lubrication", ASME J. Lubr. Technol., 100, pp.12~17 (1978)
- X. Lu, "On the Lift-off Speed in Journal Bearings", Tribology Letters, 20(3-4), pp.299~305 (2005), Springer Nature[DOI]
- Chun, S. M., "Parametric study of inlet oil temperature and pressure for a Half-Circumferential grooved journal bearing", Tribol. Trans, 35(2), pp.213~224 (1992)
- Sang Myung Chun, "Aeration effects on the performance of a turbocharger journal bearing", Tribology International, 41(4), pp.296~306 (2008), Elsevier BV[DOI]
- Majumdar, B. C., "Effect of surface roughness on elaostohydrodynamic line contact", ASME J. Lubr. Technol., (104), pp.401~409 (1982)
- Khonsari, M. M., "Applied Tribology:Bearing Design and Lubrication" (2008), Wiley
- Chang, W. R., "An elasticplastic model for the contact of rough surfaces", Trans. ASME, J. Tribol., 109, pp.257~263 (1987)
- Zhao, Y., "An asperity microcontact model incoporating the transition from elastic deformation to fully plastic flow", Trans. ASME, J. Tribol., 122, pp.86~93 (2000)
- McCool, J. I., "Relating Profile Instrument Measurements to the Functional Performance of Rough Surfaces", Trans. ASME, J. Tribol., 109(2), pp.264~270 (1987)
- Kogut, L., "Elastic-plastic contact analysis of a sphere and a rigid flat", Trans. ASME, J. Applied Mechanics, 69, pp.657~662 (2002)
- Kogut, L., "A finite element based elastic-plastic model for the contact of rough surfaces", Tribol. Trans., 46, pp.383~390 (2003)
- Masjedi, M., "Film thickness and asperity load formulas for Line-Contact elastohydrodynamic lubrication with provision for surface roughness", Trans. ASME, J. Tribol., 134(1), pp.011503~ (2012)[DOI]
- M. Masjedi, "Theoretical and experimental investigation of traction coefficient in line-contact EHL of rough surfaces", Tribology International, 70, pp.179~189 (2014), Elsevier BV[DOI]
- Kingsbury, E. P., "Some Aspect of the thermal desorption of a boundary lubricant", J. Appl. Phys, 29, pp.888~891 (1958)
- Rowe, C. N., "Some aspects of heat of adsorption in function of a boundary lubricant", ASLE Trans., 9, pp.101~111 (1966)
- Ali Beheshti, "An engineering approach for the prediction of wear in mixed lubricated contacts", Wear, 308(1-2), pp.121~131 (2013), Elsevier BV[DOI]
- Ali Beheshti, "Asperity micro-contact models as applied to the deformation of rough line contact", Tribology International, 52, pp.61~74 (2012), Elsevier BV[DOI]
- Hamrock, B. J., "Fundamentals of Fluid Film Lubrication" (1994), McGraw Hill
- Holm, R., "Electrical contacts" (1946), Almqvist & Wiksell
- Archard, J. F., "Contact and rubbing of flat surfaces", J. Appl. Phys, 24, pp.981~988 (1953)
- Sang Myung Chun, "Simulation of engine life time related with abnormal oil consumption", Tribology International, 44(4), pp.426~436 (2011), Elsevier BV[DOI]
- Ligterink, D. J., "Measurements of Wear in Radial Journal Bearings", Tribotest Journal, 3(1), pp.45~54 (1996)
- Smalley, A. J., "The effect of journal misalignment on the performance of a journal bearing under steady running conditions", Proc. Inst. Mech. Eng, 181, pp.45~54 (1966)
- Ocvirk, F. W., "Measured oil film distribution in misaligned plain bearings", J. Lubr. Eng., 10, pp.262~265 (1954)
- Stockley, J. R., "Misalignment Effects in 180° Partial Journal Bearings", ASLE Trans, 12, pp.216~226 (1969)
- Pinkus, O., "Analysis of misaligned grooved journal bearings", ASME J. Tribol, 101, pp.503~509 (1979)
- Mokhtar, M. O. A., "An analysis of misaligned journal bearings with axial and spiral feedings", Wear, 85, pp.331~337 (1983)
- Safar, Z. S., "Thermal characteristics of misaligned finite journal bearings", Tribol. Int., 18, pp.13~16 (1985)
- Ikeuchi, K., "Effects of misalignment in full journal bearing with circumferential oil groove", Proceedings of the JSLE International Tribology Conference, pp.67~72 (1985)
- Joon Jang, "On the Characteristics of Misaligned Journal Bearings", Lubricants, 3(1), pp.27~53 (2015), MDPI AG[DOI]