형광체 함유 용액 고속 토출 조건에서의 듀얼 압전 디스펜서 공이와 노즐의 마모 특성 평가
Wear Characteristics for Rod and Nozzle of Jetting Dispenser Driven by Dual Piezoelectric Actuators Under High Frequency with Phosphor-containing Liquid
1
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
An ultra-high precise ejection process is essential in a dispensing system for fabricating various precision parts such as a semiconductor, LED, and camera module. The size of such parts has been decreasing, which implies that a precise ejecting technique is required. A phosphor-containing liquid is ejected via a dispenser using dual piezoelectric actuators that are used for generating a high-speed dispensing mechanism. The rod and nozzle continuously contact in high speed to eject the liquid. However, the high-strength filler or phosphor in the liquid causes wear on the surfaces of the rod and nozzle during the dispensing process. As a result, the ejection reliability decreases as the wear on the surfaces increases. Therefore, it is necessary to estimate the wear characteristics of the rod and nozzle via an experiment and FE analysis. Reliability rests up to 1,000 cycles are conducted under relatively severe conditions. The flow rate and surfaces roughness of the rod and nozzle are measured in each ejection cycle. The surface images and wear volume are obtained before and after the tests and the ejection reliability is confirmed by measuring the flow rate of the liquid. The experimental results show that the ejection reliability is maintained up to 1,000k cycles; these results are validated by the simulation results.
Abstract
An ultra-high precise ejection process is essential in a dispensing system for fabricating various precision parts such as a semiconductor, LED, and camera module. The size of such parts has been decreasing, which implies that a precise ejecting technique is required. A phosphor-containing liquid is ejected via a dispenser using dual piezoelectric actuators that are used for generating a high-speed dispensing mechanism. The rod and nozzle continuously contact in high speed to eject the liquid. However, the high-strength filler or phosphor in the liquid causes wear on the surfaces of the rod and nozzle during the dispensing process. As a result, the ejection reliability decreases as the wear on the surfaces increases. Therefore, it is necessary to estimate the wear characteristics of the rod and nozzle via an experiment and FE analysis. Reliability rests up to 1,000 cycles are conducted under relatively severe conditions. The flow rate and surfaces roughness of the rod and nozzle are measured in each ejection cycle. The surface images and wear volume are obtained before and after the tests and the ejection reliability is confirmed by measuring the flow rate of the liquid. The experimental results show that the ejection reliability is maintained up to 1,000k cycles; these results are validated by the simulation results.
참고문헌 (7)
- Hong, S.-M., "Fabrication and Characteristics of Jetting dispenser with Dual Piezostack Acturators", Doctor, Department of Mechanical Engineering, pp.2014
- 손정우, "압전 젯팅 디스펜서의 작동 변수에 대한 실험적 분석", 한국소음진동공학회논문집, 25(10), pp.685~691 (2015), 한국소음진동공학회[DOI]
- Q. H. Nguyen, "Design of a Novel Jetting Dispenser Featuring Piezostack and Linear Pump", Journal of Intelligent Material Systems and Structures, 19, pp.333~341 (2007)
- Jeon, J. C., "Design and Performance Evaluation of a New Jetting Dispenser System Using Two Piezostack Actuators", Smart Materials and Structures, 24(1), pp.015020-1~015020-11 (2014)
- KLAASEN, H., "Performance of Cemented Carbides in Cyclic Loading Conditions", Materials Science(MEDŽIAGOTYRA), 12(2), pp.144~146 (2006)
- Klünsner, T., "Effect of microstructure on fatigue properties of WC-Co hard metals", Procedia Engineering, pp.2001~2010 (2010)
- 양희선, "가속시험법을 활용한 자동차용 워터펌프 베어링의 수명특성에 관한 연구", 한국윤활학회지, 31(2), pp.35~41 (2015), 한국윤활학회[DOI]