On the Relationship between Material Removal and Interfacial Properties at Particulate Abrasive Machining Process
0
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
In this paper, the relationship between the material removal rate and the interfacial mechanical properties at particle-surface contact situation, which can be seen in an abrasive machining process using micro/nano-sized particles, was discussed. Friction and stiffnesses were measured experimentally on an atomic force microscope (AFM) by using colloidal probes which have a silica colloid particle in place of tip to simulate a particle-flat surface contact in an abrasive machining process. From the experimental investigation and theoretical contact analysis, the interfacial contact properties such as lateral stiffness of contact, friction, the material removal rate were presented with respect to some of material surfaces and the relationship between the properties as well.
Abstract
In this paper, the relationship between the material removal rate and the interfacial mechanical properties at particle-surface contact situation, which can be seen in an abrasive machining process using micro/nano-sized particles, was discussed. Friction and stiffnesses were measured experimentally on an atomic force microscope (AFM) by using colloidal probes which have a silica colloid particle in place of tip to simulate a particle-flat surface contact in an abrasive machining process. From the experimental investigation and theoretical contact analysis, the interfacial contact properties such as lateral stiffness of contact, friction, the material removal rate were presented with respect to some of material surfaces and the relationship between the properties as well.
참고문헌 (16)
- Oliver, M, "Chemical-Mechanical Planarization of Semiconductor Materials", pp.6~7 (2004), Springer- Verlag
- Jairath, R, "Consumables for the Chemical Mechanical Polishing (CMP) of Dielectrics and Conductors", Mat. Res. Soc. Symp. Proc., 통권 : 337, pp.121~131 (1994)
- Stein, D. J, "Investigation of the Kinetics of Tungsten Chemical Mechanical Polishing in Potassium Iodate-Based Slurries: II. Roles of Colloid Species and Slurry Chemistry", J. Electrochem. Soc., 146, pp.1934~1938 (1999)
- Laursen, T, "Characterization and Optimization of Copper Chemical Mechanical Planarization", J. Electron. Mater., 31, pp.1059~1065 (2002)
- Forsberg, M, "Effect of Process Parameters on Material Removal Rate in Chemical Mechanical Polishing of Si(1 0 0)", Microelectron. Eng., 77, pp.319~326 (2005)
- Kim, H. J, "Friction and Thermal Phenomena in Chemical Mechanical Polishing", J. Mat. Proc. Technol, 130, pp.334~338 (2002)
- Sader, J. E, "Calibration of Rectangular Atomic Force Microscope Cantilevers", Rev. Sci. Instrum, 70, pp.3967~3969 (1999)
- Green, C. P, "Normal and Torsional Spring Constants of Atomic Force Microscope Cantilevers", Rev. Sci. Instrum, 75, pp.1988~1996 (1995)
- Ogletree, D. F, "Calibration of Frictional Forces in Atomic Force Microscopy", Rev. Sci. Instrum, 67, pp.3298~3306 (1996)
- Cleveland, J. P, "A Nondestructive Method for Determining the Spring Constant of Cantilevers for Scanning Force Microscopy", Rev. Sci. Instrum, 64, pp.403~405 (1993)
- Lantz, M. A, "Lateral Stiffness of the Tip and Tipsample Contact in Frictional Force Microscopy", Appl. Phys. Lett, 70, pp.970~972 (1997)
- Seok, J, "Multiscale Material Removal Modeling of Chemical Mechanical Polishing", Wear, 254, pp.307~320 (2003)
- Lafaye, S, "On the Friction Behaviour in Nanoscratch Testing", Wear, 261, pp.905~913 (2006)
- Kaupp, G, "Atomic Force Microscopy, Scanning Nearfield Optical Microscopy and Nanoscratching", pp.229~252 (2006), Springer-Verlag
- Fischer-Cripps, A. C, "Nanoindentation", pp.1~19 (2002), Springer-Verlag
- Sung, I. H, "Nanomechanical Characteristics at Ultrasmall Particle-Surface Contact Interface", Journal of Mechanical Science and Technology