고강력 직물의 열융착 라미네이팅을 통한 충격 완화용 에어쿠션 소재로의 적용 가능성 검토 연구
Study on the Applicability of the Air Cushion Material for Impact Relief through Thermal Bonding of High Strength Fabrics
2
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
In order to study wearable air cushion materials capable of responding to massive impact in high-altitude fall situation, high tenacity woven fabrics were bonded by heat only depending on various type of thermoplastic films and then mechanical properties were measured. Tensile strength, elongation, and 100% modulus measurement results for 4 types of films show that TPU-2 has higher impact resistance and easier expansion than PET-1. After thermal bonding, the combination with the highest tensile strength was a material with a TPU-2 film for nylon and a PET-2 film for PET, so there was a difference by type of fabric. The tear strength of the bonded materials were increased compared to the fabric alone, which shows that durability against damage such as tearing can be obtained through film adhesion. All of the peel strengths exceeded the values r e quired by automobile airbags by about 5 times, and the TPU-2 bonded fabric showed the highest value. The air permeability was 0 L/dm2/min. For both the film and the bonded material, which means tightness between the fabric and the film through thermal bonding. It is expected to be applied as a wearable air cushion material by achieving a level of mechanical properties similar to or superior to that of automobile airbags through the method of bonding film and fabric by thermal bonding.
Abstract
In order to study wearable air cushion materials capable of responding to massive impact in high-altitude fall situation, high tenacity woven fabrics were bonded by heat only depending on various type of thermoplastic films and then mechanical properties were measured. Tensile strength, elongation, and 100% modulus measurement results for 4 types of films show that TPU-2 has higher impact resistance and easier expansion than PET-1. After thermal bonding, the combination with the highest tensile strength was a material with a TPU-2 film for nylon and a PET-2 film for PET, so there was a difference by type of fabric. The tear strength of the bonded materials were increased compared to the fabric alone, which shows that durability against damage such as tearing can be obtained through film adhesion. All of the peel strengths exceeded the values r e quired by automobile airbags by about 5 times, and the TPU-2 bonded fabric showed the highest value. The air permeability was 0 L/dm2/min. For both the film and the bonded material, which means tightness between the fabric and the film through thermal bonding. It is expected to be applied as a wearable air cushion material by achieving a level of mechanical properties similar to or superior to that of automobile airbags through the method of bonding film and fabric by thermal bonding.
참고문헌 (21)
- H. S. Choi, "Korea Pat. 10-2010-0127668", ~ (2010)
- P. Russo, "Thermoplastic Polyurethane Films Reinforced with Carbon Nanotubes: The Effect of Processing on the Structure and Mechanical Properties", European Polymer Journal, 49, pp.379~ (2013)
- J. H. Yoon, "Korea Pat. 10-2015-0085379", ~ (2015)
- S. K. Kim, "Korea Pat. 10-2017-0170363", ~ (2017)
- K. J. Kim, "Korea Pat. 10-2012-0158574", ~ (2012)
- E. Shim, "Joining Textiles", pp.309~351 (2013), Woodhead Publishing
- V. E. Keeley, "Transfer Coating with Polyurethanes", Journal of Coated Fabrics, 20(1), pp.176~ (1991)
- G. Yao, "Development of Airbag Fabrics by Polyester Filament", Proceedings of 3rd International Conference on Materials, Mechanical and Manufacturing Engineering, pp.1566~ (2015)
- 이경, "전기방사한 나노섬유 웹 라미네이트 소재의 반복 세탁에 따른 투습방수 성능 변화 및 내구성", 한국의류산업학회지, 14(1), pp.122~129 (2012), 한국의류산업학회
- Development of Laminating Technology using Thermoplastic Polyurethane Hot-melt Film with excellent Breathability, "D. G. Kim", Ministry of SMEs and Startups, 67~85 (2013)
- R. R. Hegde, "Influence of Material Variables in Thermal Bonding of Nonwovens", M. S., pp.2006
- Z. Jakubcioniene, "Investigation of the Strength of Textile Bonded Seams", Materials Science, 18(2), pp.172~ (2012)
- Q. Yu, "Study on Creating the Three-dimensional Shape of Apparel by Thermal Bonding of Thermoplastic Polyurethane Film and Vacuum Forming Molding", Journal of Engineered Fibers and Fabrics, 15(1-9), pp.1~ (2020)
- 한영철, "Polyethylene Glycol의 분자량 및 NCO index의 변화에 따른 Hydrophilic Reactive Hotmelt Polyurethane의 물성 변화", 한국염색가공학회지, 30(2), pp.90~97 (2018), 한국염색가공학회[DOI]
- 이영희, "Effect of Hot Pressing", Melt Mixing on the Properties of Thermoplastic Polyurethane, 2009, pp.17(8), 616~622[DOI]
- G. Chen, "Influence of Different Airbag Fabrics on Airbag Performance", Advanced Materials Research, 332, pp.1053~ (2011)
- 서석훈, "바이오 폴리올을 이용한 인공피혁 코팅용 폴리우레탄의 합성 및 특성", 한국염색가공학회지, 30(4), pp.321~328 (2018), 한국염색가공학회[DOI]
- K. Kojio, "Control of Mechanical Properties of Thermoplastic Polyurethane Elastomers by Restriction of Crystallization of Soft Segment", Materials, 3(12), pp.5097~ (2010)
- J. Wei, "Strength Testing of Fabric Composite Material and Impact Simulation for Airbag Landing System", Advanced Materials Research, 1095, pp.463~ (2015)
- D. Vlad, "Research Regarding Uniaxial Tensile Strength of Nylon Woven Fabrics, Coated and Uncoated with Silicone", Proceedings of the MATEC Web of Conferences, 290, pp.1~ (2019)
- M. J. Choi, "Korea Pat. 10-2009-0134534", ~ (2009)