Ni-Al계 금속간화합물의 고주파 연소합성코팅에 미치는볼 밀링의 영향
Effects of Ball Milling for Elemental Powders on Ni-Al based Intermetallics Coating on Mild Steel through Induction Heating Process
2
조회
0
다운로드
3
인용
0
참고문헌
키워드
초록
Ball milling of elemental powders in advance and using an induction heating system for intermetallic coatings are known to enhance the reactivity of combustion synthesis. In this work, the effects of simultaneously applying these two incentive methods on the properties of intermetallic coatings are studied. Ni–Al powder compacts ball-milled with three different ball-to-powder weight ratio mixtures are synthesized and coated on mild steel by combustion synthesis in an induction heating system. Consequently, similar to an electrical heating system, the positive effects of ball milling on the combustion synthesis are confirmed in the induction heating system. The enhancement in synthetic reactivity achieved by applying the two incentive methods at the same time is greater than that by applying each incentive method separately. In particular, the enhancement is remarkable at low reaction temperature. However, there are limitations to improving the reactivity by simultaneously applying the two incentive methods to the combustion synthesis, unlike the reaction temperature. The microstructure and hardness of the coating layer are both influenced by the ball-charging ratio employed in the ball-milling process.
Abstract
Ball milling of elemental powders in advance and using an induction heating system for intermetallic coatings are known to enhance the reactivity of combustion synthesis. In this work, the effects of simultaneously applying these two incentive methods on the properties of intermetallic coatings are studied. Ni–Al powder compacts ball-milled with three different ball-to-powder weight ratio mixtures are synthesized and coated on mild steel by combustion synthesis in an induction heating system. Consequently, similar to an electrical heating system, the positive effects of ball milling on the combustion synthesis are confirmed in the induction heating system. The enhancement in synthetic reactivity achieved by applying the two incentive methods at the same time is greater than that by applying each incentive method separately. In particular, the enhancement is remarkable at low reaction temperature. However, there are limitations to improving the reactivity by simultaneously applying the two incentive methods to the combustion synthesis, unlike the reaction temperature. The microstructure and hardness of the coating layer are both influenced by the ball-charging ratio employed in the ball-milling process.
참고문헌 (15)
- Izumi, O., "Intermetallics, Chap. 4", pp.54~ (1990), Sangyotosho
- Materials Sci. Soc. of JPN, "Intermetallic Compounds for Materials, Chap. 3", pp.88~ (1995), Shokabo
- Salehi, M., "Formation of TiNi Intermetallic coatings on carbon tool steel by a duplex process", Surface and Coatings Technology, 148, pp.55~60 (2000)
- Lee, H. -Y., "The effects of induction heating rate on properties of Ni-Al based intermetallic compound layer coated on ductile cast iron by combustion synthesis", Intermetallics, 15, pp.1050~1055 (2007)
- 이한영, "Ni-Al계 금속간화합물 코팅에 미치는 고주파유도 가열 조건의 영향", 대한금속·재료학회지, 48(2), pp.141~147 (2010), 대한금속·재료학회
- Lee, H. -Y., "Sliding wear properties for Ni-Al based intermetallic compound layer coated on ductile cast iron by combustion synthesis", Wear, 260, pp.83~89 (2006)
- 이한영, "저온 연소합성 후 확산 열처리한 Ni3Al 금속간화합물 코팅층의 미끄럼 마모거동", 한국윤활학회지, 25(1), pp.7~12 (2009), 한국윤활학회
- Okamoto, A., "Effects of silicon addition on nickel-aluminide surface coatings through combustion synthesis", J. of Jpn. Foundrymens Society, 77, pp.744~751 (2005)
- Kimata, T., "Enhanced densification of combustion synthesized Ni-Al intermetallic compound by si addition", Intermetallics, 11, pp.947~952 (2003)
- 이한영, "주철의 용탕열을 이용한 Ni-Al계 금속간화합물의 연소합성 코팅에 미치는 Ball Milling의 영향", 대한금속·재료학회지, 50(1), pp.28~33 (2012), 대한금속·재료학회
- 이한영, "Cu-Al-Ni계 금속간화합물의 연소합성 Coating에 미치는 Ball Mill처리의 영향", 한국윤활학회지, 27(1), pp.1~6 (2011), 한국윤활학회
- Sanchez, C., "NiAl intermetallic coatings elaborated by solar assisted SHS process", Intermetallics, 14, pp.1270~1275 (2006)
- Van Dyck, S., "Reactive powder metallurgy of Ni3Si-based alloys", Intermetallics, 3, pp.309~314 (1995)
- 이한영, "고주파 유도가열을 통한 알루미늄 기판재위 Ni-Al계 금속간화합물의 연소합성코팅에 관한 연구", 한국윤활학회지, 28(2), pp.56~61 (2012), 한국윤활학회
- Morsi, K., "Reaction synthesis processing of Ni-Al intermetallic materials", Mater. Sci. Eng., (A299), pp.1~15 (2001)