브로칭 가공된 회주철 소재 표면의 마찰 및 마모 특성
Friction and Wear Characteristics of Gray Cast Iron Surface Processed by Broaching Method
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
In this work the friction and wear characteristics of the gray cast iron surface processed by broaching method, which is widely used in the machinery industry, were investigated. The broaching process is mainly used for mass production because it has high dimensional accuracy and processing speed, but the defects on surface can be easily generated. In order to improve the tribological characteristics, the approach was to reduce the roughness and hardness of the surface by adding a machining process to the broaching specimen. The secondary machining process using abrasive grains produces low roughness and hardness than broaching because it has high tool accuracy and removes the work hardened surface. The friction coefficient and the wear rate were assessed using a reciprocating-type tribotester to analyze the effects of surface finishing on the tribological properties. The friction tests were conducted under dry and lubricated conditions. The test results showed that the reduction of surface roughness and hardness through secondary machining process in lubricated condition improved the friction and wear characteristics. The reason why the same results did not appear in a dry condition was that wear occurred more rapidly than in lubricated condition. Thus, the positive effect of roughness and hardness of the surface obtained through the secondary machining process was not observed.
Abstract
In this work the friction and wear characteristics of the gray cast iron surface processed by broaching method, which is widely used in the machinery industry, were investigated. The broaching process is mainly used for mass production because it has high dimensional accuracy and processing speed, but the defects on surface can be easily generated. In order to improve the tribological characteristics, the approach was to reduce the roughness and hardness of the surface by adding a machining process to the broaching specimen. The secondary machining process using abrasive grains produces low roughness and hardness than broaching because it has high tool accuracy and removes the work hardened surface. The friction coefficient and the wear rate were assessed using a reciprocating-type tribotester to analyze the effects of surface finishing on the tribological properties. The friction tests were conducted under dry and lubricated conditions. The test results showed that the reduction of surface roughness and hardness through secondary machining process in lubricated condition improved the friction and wear characteristics. The reason why the same results did not appear in a dry condition was that wear occurred more rapidly than in lubricated condition. Thus, the positive effect of roughness and hardness of the surface obtained through the secondary machining process was not observed.
참고문헌 (21)
- Sutherland, J. W., "A model for the cutting force system in the gear broaching process", Int. J. Mach. Tools Manuf, 37(10), pp.1409~1421 (1997)
- Jia, K., "Grinding path planning for the cutting teeth of helical broaching tool", Int. J. Mach. Tools Manuf, 89(1-4,), pp.87~100 (2017)
- Bathe, R., "Laser surface texturing of gray cast iron for improving tribological behavior", Appl. Phys. AMater. Sci. Process, 117(1), pp.117~123 (2014)
- Ooi, K. T., "Design optimization of a rolling piston compressor for refrigerators", Appl. Therm. Eng., 25(5-6), pp.813~829 (2005)
- De Mello, J. D. B., "Effect of the actual environment present in hermetic compressors on the tribological behaviour of a Si-rich multifunctional DLC coating", Wear, 267(5-8), pp.907~915 (2009)
- Hu, X., "Theoretical study on frictional losses of a novel automotive swing vane compressor", Int. J. Refrig, 36(3), pp.758~767 (2013)
- Mishra, S. P., "Tribological studies of unpolished laser surface textures under starved lubrication conditions for use in air-conditioning and refrigeration compressors", Tribol. Int, 44(12), pp.1890~1901 (2011)
- Etsion, I., "Improving tribological performance of mechanical components by laser surface texturing", Tribol. Lett, 17(4), pp.733~737 (2004)
- An experimental study of piston skirt roughness and profiles on piston friction using the floating liner engine, "Westerfield, Z.", SAE, ~ (2016)
- Khagendra Tripathi, "Graphene Coating via Chemical Vapor Deposition for Improving Friction and Wear of Gray Cast Iron at Interfaces", ACS Applied Materials & Interfaces, 9(37), pp.32336~32351 (2017), American Chemical Society (ACS)[DOI]
- Timothy A. Solzak, "Tribology of Hard Protective Coatings Under Realistic Operating Conditions for Use in Oilless Piston-Type and Swash-Plate Compressors", Tribology Transactions, 53(3), pp.319~328 (2010), Informa UK Limited[DOI]
- A.R. Riahi, "Wear map for grey cast iron", Wear, 255(1-6), pp.401~409 (2003), Elsevier BV[DOI]
- Evans, C. J., "Material removal mechanisms in lapping and polishing", CIRP Ann-Manuf. Technol, 52(2), pp.611~633 (2003)
- Welling, D., "Results of surface integrity and fatigue study of wire-EDM compared to broaching and grinding for demanding jet engine components made of Inconel 718", Procedia CIRP, 13, pp.339~344 (2014)
- Grzesik, W., "Characterization of surface textures generated on hardened steel parts in high-precision machining operations", Int. J. Adv. Manuf. Technol., 78(9-12), pp.2049~2056 (2015)
- Sedlaček, M., "Influence of surface preparation on roughness parameters, friction and wear", Wear, 266(3-4), pp.482~487 (2009)
- 김현준, "Nano-Lubrication: A Review", International Journal of Precision Engineering and Manufacturing, 17(6), pp.829~841 (2016), 한국정밀공학회
- 김현준, "Nano-scale Friction : A Review", International Journal of Precision Engineering and Manufacturing, 10(2), pp.141~151 (2009), 한국정밀공학회
- 김해진, "Nano-scale Wear: A Review", International Journal of Precision Engineering and Manufacturing, 13(9), pp.1709~1718 (2012), 한국정밀공학회
- 원성재, "오일샌드 플랜트용 금속소재의 마모 특성에 대한 실험적 연구", 한국트라이볼로지학회지, 33(1), pp.31~35 (2017), 한국트라이볼로지학회[DOI]
- 변상민, "Ductile Cast Iron (DCI) 롤의 마모 특성 고찰 및 마모계수 도출을 위한 실험적 연구", 한국트라이볼로지학회지, 33(3), pp.98~105 (2017), 한국트라이볼로지학회[DOI]