의료용 폴리머 소재를 활용한 3D 프린팅 인공치아용사면체 비정질 카본 코팅 기술 연구
A Study on the Tetrahedral Amorphous Carbon (ta-C) Coating on Medical Polymer Materials for 3D Printing Artificial Teeth
0
조회
0
다운로드
3
인용
0
참고문헌
키워드
초록
This research presents tetrahedral amorphous (ta-C) coating on the artificial tooth for improving the durability and functionality (esthtics, foreign body of tooth) by filtered cathodic vacuum arc (FCVA). A differentiated coating method is required for a ta-C coating on polymer owing to the low melting point of the polymer, inter-facial adhesion, low friction, and non-conductivity. Herein, ta-C coating is applied below 50oC, and the potential difference of the carbon plasma drawn to the substrate was controlled by applying a positive duct bias voltage without using a substrate bias voltage. Consequently, the ta-C coating with a thickness of 70nm using the duct bias condition of 20V with the highest plasma intensity satisfies the esthetics of the artificial tooth and had a 5B level of inter-facial adhesion. In addition, the composite hardness of ta-C/polymer is 380 MPa, and correlations with esthetics, sp3 bonding, and mechanical properties. The friction coefficient (CoF) of the ta-C coating in a water-lubricated environment is 0.07, showing a six-fold reduction in CoF compared with that of a polymer.
Abstract
This research presents tetrahedral amorphous (ta-C) coating on the artificial tooth for improving the durability and functionality (esthtics, foreign body of tooth) by filtered cathodic vacuum arc (FCVA). A differentiated coating method is required for a ta-C coating on polymer owing to the low melting point of the polymer, inter-facial adhesion, low friction, and non-conductivity. Herein, ta-C coating is applied below 50oC, and the potential difference of the carbon plasma drawn to the substrate was controlled by applying a positive duct bias voltage without using a substrate bias voltage. Consequently, the ta-C coating with a thickness of 70nm using the duct bias condition of 20V with the highest plasma intensity satisfies the esthetics of the artificial tooth and had a 5B level of inter-facial adhesion. In addition, the composite hardness of ta-C/polymer is 380 MPa, and correlations with esthetics, sp3 bonding, and mechanical properties. The friction coefficient (CoF) of the ta-C coating in a water-lubricated environment is 0.07, showing a six-fold reduction in CoF compared with that of a polymer.
참고문헌 (11)
- "Analysis of industrial structure effect according to 3D printing development" (2015), Korea Electronics Association, (KTA)
- "Regulations on medical device items and classification by item, Characteristic evaluation item specifications of temporary crown resin dental materials"[URL]
- Jang, Y. J, "Friction properties of thick tetrahedral amorphous carbon coating with different surface defects under dry contact conditions", Applied Surface Science (2021)[DOI]
- 강용진, "공정 온도에 따른 사면체 비정질 카본 (ta-C) 코팅의트라이볼로지적 특성연구", 한국트라이볼로지학회지, 35(6), pp.362~368 (2019), 한국트라이볼로지학회[DOI]
- 장영준, "DLC (ta-C) 후막코팅을 위한 트라이볼로지 코팅 연구", 한국트라이볼로지학회지, 32(4), pp.125~131 (2016), 한국트라이볼로지학회[DOI]
- "ISO 22598:2020, “Dentistry-Colur tabs for introral tooth colour determination”", ~ (2020)
- Jang, Y. J, "A study on thick coatings of tetrahedral amorphous carbon deposited by filtered cathde vacuum arc plasma", J. Mater. Res, 31(3) (2016)[DOI]
- "ASTM Standard D3359-17:2017, Standard Test Methods for Rating Adhesion by Tape Test", ~ (2017)
- 박태조, "유한요소해석에 의한 코팅면의 브리넬 경도 평가: 제2보-모재와 코팅두께의 영향", 한국트라이볼로지학회지, 37(4), pp.144~150 (2021), 한국트라이볼로지학회[DOI]
- Noda, M, "Microstructure and optical band gap control of DLC deposited by pulsed dischage plasma CVD", Diamond and Related Mateirals, 17 (2008)[DOI]
- Alam, N. S, "Optical properties of diamond like carbon nanocomposite thin films", AIP Conference Proceedings, 1953 (2018)