Micro-CT를 이용한 맞춤형 CAD-CAM 지대주의 적합성 분석
Fit analysis of CAD-CAM custom abutment using micro-CT
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
목적: Biomet 3i 시스템과 Astra 시스템의 내측 연결형 임플란트 고정체에 국내에서 제작된 맞춤형 CAD-CAM 지대주를 체결하여 구성 성분 간의 적합성과 나사의 안정성을 평가하고자 하였다. 재료 및 방법: 24개 3i 임플란트 중 12개의 임플란트에 기성 지대주를 연결하고, 나머지 임플란트에는 맞춤형 CAD-CAM 지대주를 연결하여 각각Group 1과 Group 2로 분류하였다. 동일 개수와 동일한 방법으로 Astra 임플란트를 각각 Group 3와 Group 4로 분류하였다. 각각의 고정체에 지대주를 장착하여 각 계면 사이의 적합성을 micro-CT로 관찰하고 초기 풀림 토크를 측정한 후 평가하였다. 결과: 고정체-지대주의 접촉길이는 Group 1과 Group 2 사이 뿐만 아니라 Group 3와 Group 4 사이에도 유의한 차이가 없었다(Mann-Whitney test, P>.05). 하지만, 지대주와 나사의 계면 및 고정체와 나사의 계면에서 Group 2와 Group 4가 Group 1와 Group 3에 비해 각기 더 큰 접촉양상을 보여주었다(Mann-Whitney test, P<.05). 또한, Group 2와 Group 4가 Group 1과 Group 3에 비해 각기 더 낮은 나사의 초기 풀림 토크를 기록하였다(Student t-test, P<.05). 결론: CAD-CAM지대주는 임상에 적용할 만한 적합성을 지니고 있으나, 광범위한 임상 적용을 위해서는 풀림 토크가 향상되어야 할 것으로 사료된다.
Abstract
Purpose: The purpose of this study was to investigate screw joint stability and sagittal fit between internal connection implant fixtures of two different manufacturers and customized abutments. Materials and methods: Internal connection implant systems from two different manufacturers (Biomet 3i system, Astra Tech system) were selected for this study (n=24 for each implant system, total n=48). For 3i implant system, half of the implants were connected with Ti ready-made abutments and the other half implants were connected with Ti CAD-CAM custom ones of domestic-make (Myplant, Raphabio Co., Seoul, Korea) and were classified into Group 1 and Group 2 respectively. Astra implants were divided into Group 3 and Group 4 in the same way. Micro-CT sagittal imaging was performed for fit analysis of interfaces and preloading reverse torque values (RTV) were measured. Results: In the contact length of fixture-abutment interface, there were no significant differences not only between Group 1 and Group 2 but also between Group 3 and Group 4 (Mann-Whitney test, P>.05). However, Group 2 and Group 4 showed higher contact length significantly than Group 1 and Group 3 in abutmentscrew interface as well as fixture-screw one (Mann-Whitney test, P<.05). In addition, RTV was lower in CAD-CAM custom abutments compared to ready-made ones (Student t-test, P<.05). Conclusion: It is considered that domestically manufactured CAD-CAM custom abutments have similar fit at the fixture abutment interface and it could be used clinically. However, RTV of CAD-CAM custom abutments should be improved for the increase of clinical application.
참고문헌 (30)
- Sumi T, "Characteristics of implant-CAD", CAM abutment connections of two different internal connection systems, 2012, pp.39, 391~398
- Lang LA, "Evaluation of the precision of fit between the Procera custom abutment and various implant systems", Int J Oral Maxillofac Implants, 18, pp.652~658 (2003)
- Bichacho N, "Achieving optimal gingival esthetics around restored natural teeth and implants. Rationale, concepts, and techniques", Dent Clin North Am, 42, pp.763~780 (1998)
- 김형섭, "CAD", CAM 시스템을 이용한 Custom abutment의 제작, 2012, pp.50(3), 118~125[DOI]
- Lewis SG, "The UCLA abutment: a four-year review", J Prosthet Dent, 67, pp.509~515 (1992)
- Wu T, "Design of a custom angled abutment for dental implants using computer-aided design and nonlinear finite element analysis", J Biomech, 43, pp.1941~1946 (2010)
- Sailer I, "Randomized controlled clinical trial of customized zirconia and titanium implant abutments for canine and posterior single-tooth implant reconstructions: preliminary results at 1 year of function", Clin Oral Implants Res, 20, pp.219~225 (2009)
- Kerstein RB, "Ideal gingival form with computer-generated permanent healing abutments", Compend Contin Educ Dent, 21, pp.793~797 (2000)
- Priest G, "Virtual-designed and computer-milled implant abutments", J Oral Maxillofac Surg, 63, pp.22~32 (2005)
- Martin WC, "Implant abutment screw rotations and preloads for four different screw materials and surfaces", J Prosthet Dent, 86, pp.24~32 (2001)
- Boggan RS, "Influence of hex geometry and prosthetic table width on static and fatigue strength of dental implants", J Prosthet Dent, 82, pp.436~440 (1999)
- Abrahamsson I, "Soft tissue response to plaque formation at different implant systems. A comparative study in the dog", Clin Oral Implants Res, 9, pp.73~79 (1998)
- Quirynen M, "Microbial penetration along the implant components of the Brånemark system. An in vitro study", Clin Oral Implants Res, 5, pp.239~244 (1994)
- Henriksson K, "Evaluation of custom-made procera ceramic abutments for single-implant tooth replacement: a prospective 1-year follow-up study", Int J Prosthodont, 16, pp.626~630 (2003)
- Canullo L, "Clinical outcome study of customized zirconia abutments for single-implant restorations", Int J Prosthodont, 20, pp.489~493 (2007)
- Swain MV, "State of the art of Micro-CT applications in dental research", Int J Oral Sci, 1, pp.177~188 (2009)
- Pelekanos S, "Micro-CT evaluation of the marginal fit of different In-Ceram alumina copings", Eur J Esthet Dent, 4, pp.278~292 (2009)
- Suomalainen AK, "The 3DX multi image micro-CT device in clinical dental practice", Dentomaxillofac Radiol, 36, pp.80~85 (2007)
- Siamos G, "Relationship between implant preload and screw loosening on implant-supported prostheses", J Oral Implantol, 28, pp.67~73 (2002)
- 김종욱, "기성 지대주와 맞춤형 CAD-CAM 지대주의 적합 및 나사 안정성 비교", 대한치과보철학회지, 51(4), pp.276~283 (2013), 대한치과보철학회[DOI]
- 김낙형, "임플란트-지대주-나사의 적합에 관한 연구", 대한치과보철학회지, 41(4), pp.503~518 (2003), 대한치과보철학회
- Jung SH, "A comparative study on the fit in prostheses using premade gold cylinder and plastic cylinder", J Korean Acad Prosthodont, 37, pp.825~834 (1999)
- 이흥태, "내측연결 임플란트 시스템에서 고정체와 지대주 연결부의 적합에 관한 연구", 대한치과보철학회지, 42(2), pp.192~209 (2004), 대한치과보철학회
- de Morais Alves da Cunha T, "Comparison of fit accuracy between Procera custom abutments and three implant systems", Clin Implant Dent Relat Res, 14, pp.890~895 (2012)
- Binon PP, "Evaluation of machining accuracy and consistency of selected implants, standard abutments, and laboratory analogs", Int J Prosthodont, 8, pp.162~178 (1995)
- 장종석, "코팅된 지대주 나사의 반복 착탈 후 풀림력과 표면변화에 대한 연구", 대한치과보철학회지, 46(5), pp.500~510 (2008), 대한치과보철학회
- Yeo IS, "The effect of abutment screw length on screw loosening in dental implants with external abutment connections after thermocycling", Int J Oral Maxillofac Implants, 29, pp.59~62 (2014)
- 이주리, "다수 임플란트 지지 보철물에서 지대주 나사의 풀림 토크값에 대한 연구", 대한치과보철학회지, 48(04), pp.280~286 (2010), 대한치과보철학회
- 이창재, "CAD", CAM을 이용한 맞춤형 임플란트 지대주의 나사 풀림 토크 평가, 2012, pp.50(2), 128~134[DOI]
- Haack JE, "Elongation and preload stress in dental implant abutment screws", Int J Oral Maxillofac Implants, 10, pp.529~536 (1995)