항공용 고속 롤러베어링의 냉각 방식에 따른 작동간극 변화
Variation of Operating Clearance Depending on Cooling Methods of High-Speed Roller Bearings for Aerospace Applications
0
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
In this study, the expansion, stress, and operating clearance of bearing elements during operation are observed using the inner/outer ring temperature test data of a 3.0×106 DN-class roller bearing. The operating clearance characteristics of inner-/outer-ring cooling (IORC) bearings are compared to those of inner-ring cooling (IRC) bearings. For IRC bearings, the thermal expansion of the outer ring is the most important factor in clearance variation. As a result, the operating clearance is less than the initial clearance of 61 μm, and the operating clearance decreases to 0.5 μm at 25,500 rpm. Conversely, the temperature of the outer ring of IORC bearings is lower than that of IRC bearings, so the operating clearance is kept smaller. When the coolant flow rate to the outer ring is approximately 1.5 to 2.0 L/min, the temperature difference between the inner and outer rings is minimized and the operating clearance is maintained at a significantly lower level than IRC bearings. Small operating clearances are expected to be effective in reducing cage slip and skid damage in roller bearings. The results and analysis procedures of this study can be utilized to design of bearing clearance, lubricant flow rate, and assembled interference in the early design stage of aerospace roller bearings.
Abstract
In this study, the expansion, stress, and operating clearance of bearing elements during operation are observed using the inner/outer ring temperature test data of a 3.0×106 DN-class roller bearing. The operating clearance characteristics of inner-/outer-ring cooling (IORC) bearings are compared to those of inner-ring cooling (IRC) bearings. For IRC bearings, the thermal expansion of the outer ring is the most important factor in clearance variation. As a result, the operating clearance is less than the initial clearance of 61 μm, and the operating clearance decreases to 0.5 μm at 25,500 rpm. Conversely, the temperature of the outer ring of IORC bearings is lower than that of IRC bearings, so the operating clearance is kept smaller. When the coolant flow rate to the outer ring is approximately 1.5 to 2.0 L/min, the temperature difference between the inner and outer rings is minimized and the operating clearance is maintained at a significantly lower level than IRC bearings. Small operating clearances are expected to be effective in reducing cage slip and skid damage in roller bearings. The results and analysis procedures of this study can be utilized to design of bearing clearance, lubricant flow rate, and assembled interference in the early design stage of aerospace roller bearings.
참고문헌 (19)
- 김기태, "항공용 가스터빈 엔진에서의 트라이 볼로지", J. Korean Soc. Tribol. Lubr. Eng, 13(3), pp.1~9 (1997)[DOI]
- "ISO 281:2007(E), Rolling Bearings-Dynamic Load Ratings and Rating Life"
- Tassone, B. A., "Roller Bearing Slip and Skidding Damage", J. Aircraft, 12(4), pp.181~187 (1975)
- Tassone, B. A., "Roller Bearing Slip and Skidding Damage", J. Aircr, 12(4), pp.281~287 (1975)
- Operating Characteristics of a Large-Bore Roller Bearing to Speeds of 3 × 106 DN, "Schuller, F. T.", NASA, ~, pp.NASA Technical Paper 1413 (1979)
- Zhang, Q., "Experimental Study on the Skidding Damage of a Cylindrical Roller Bearing", Applied Materials, 13(4075), pp.1~20 (2020)
- Chang, L., "Analysis of High-Speed Cylindrical Roller Bearings Using a Full Elastohydrodynamic Lubrication Model Part 2 : Results", Tribol. Trans, 33(2), pp.85~291 (1990)
- Poplawski, J. V., "Slip and Cage Forces in a High-Speed Roller Bearing", ASME. J. Lubr. Tech, 94(2), pp.143~150 (1971)
- Dadouch, A., "Roller Bearing Skidding for Aero-Engine Applications : All-Steel Versus Hybrid Bearings", ASME Journal of Engineering for Gas Turbines and Power, 145(1), pp.011004~ (2023)
- Dadouch, A., "Bearing Skidding Detection for High-Speed and Aero-Engine Applications", ASME Journal of Engineering for Gas Turbines and Power, 144(3), pp.031003~ (2022)
- 김선제, "Analytical consideration of the radial clearance to reduce cage slip of the turbo engine roller bearing", Journal of Mechanical Science and Technology, 35(7), pp.2827~2839 (2021), 대한기계학회[DOI]
- Dawoud, M., "Slip Characteristics in Cylindrical Roller Bearings-Part III : Influence of Bearing Clearance on the Roller and Set Slip", Journal of Tribology, 145(2), pp.021205~ (2022)
- Operating Characteristics of a Three-Piece-Inner-Ring Large-Bore Roller Bearing to Speeds of 3 Million DN, "Schuller, F. T.", NASA, ~, pp.NASA Technical Paper 2355 (1984)
- Cao, H., "Study of Characteristic Variations of High-Speed Spindles Induced by Centrifugal Expansion Deformations", J. VibroEngineering, 14(3), pp.1278~1291 (2012)
- Park, J., "Rotordynamic Analysis of Gas Foil-Polymer Bearings Based on a Structural Elasticity Model of Polymer Layer along with Static-Load Deflection Tests", Appl. Sci, 11(4), pp.1789~ (2021)
- Brinson, H. F., "Polymer Engineering Science and Viscoelasticity" (2010), Springer
- Effect of Hoop Stress on Ball Bearing Life Prediction, "Zaretsky, E. V.", NASA, ~, pp.NASA Technical Memorandum 106874 (1995)
- Coe, H. H., "Effect of Interference Fits on Roller Bearing Fatigue Life", ASLE Transactions, 30(2), pp.131~140 (1987)
- Effect of Internal Clearance on Load Distribution and Life of Radially Loaded Ball and Roller Bearings, "Oswald, F. B.", NASA, ~, pp.NASA (2012), TM-2012-217115