광중합기의 광원에 따른 브라켓 전단결합강도 비교
Comparison of the shear bond strength of brackets in regards to the light curing source
1
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
제논 플라즈마 아크 광중합기나 LED 광중합기가 치과영역에 소개된 이후로 기존의 텅스텐 할로겐 광중합기를 사용할 때에 비해 교정장치의 부착시간이 현저하게 줄어들 수 있게 되었다. 제논 플라즈마 아크 광중합기에 대한 중합시간과 전단강도에 대해서는 여러 연구가 있어왔던 반면, LED 광중합기를 이용하여 교정용장치의 부착을 위한 중합시간에 대한 연구는 미진하다. 본 연구의 목적은 LED 광중합기의 중합시간에 따른 결합강도를 플라즈마 아크 광중합기와 비교하여 적절한 브라켓의 부착강도를 얻기 위해 요구되는 중합시간을 알아보는데 있다. 120개의 발치된 사람의 소구치에 컴포짓 레진으로 브라켓을 부착시킨 후 4초, 6초, 8초 동안 플라즈마 아크 광원과 LED 광원으로 각각 중합시켰다. 그 후 결합강도를 만능시험기(Universal Testing Machine)로 계측한 결과, 플라즈마 아크 광중합기에서는 4초 이상에서, LED 광중합기에서는 8초 이상의 중합시간에서 기존의 할로겐 광원을 40초간 노출시켰을 때와 비슷한 전단결합강도를 나타내었다. 플라즈마 아크 광중합기와 LED 광중합기의 중합시간이 접착제 잔류지수(adhesive remnant index) 수치에 대해 영향을 미치지 않았다.
Abstract
With the introduction of the xenon plasma arc curing light and the LED curing light as orthodontic curing lights, the polymerizing time of orthodontic composites has clearly decreased. In contrast to various research cases regarding the polymerization time and bond strength of the xenon plasma arc curing light, not enough research exists on the LED curing light, including the appropriate polymerization time. The objective of this research was to compare the bond strength of the plasma curing light and the LED curing light in regards to the polymerization time. The polymerization time needed to achieve an appropriate adhesion strength of the bracket has also been studied. After applying orthodontic brackets using composite resin onto 120 human premolars, the plasma arc curing light and the LED curing light were used for polymerization for 4, 6, and 8 seconds accordingly. This research proved that the LED curing light provided appropriate bond strength for mounting orthodontic brackets even with short seconds of polymerization. The expensive cost and large size of the device limits the use of the plasma arc curing light, whereas the low cost and easy handling of the LED curing light may lead to greater use in orthodontics.
참고문헌 (36)
- "Visible lights and visible light-activated composite resins", 50, pp.31~35 (1983)
- "Comparative bond strength of brackets cured using a pulsed xenon curing light with 2 different light-guide sizes", 122, pp.242~250 (2002)
- "Rapid curing of bonding composite with a xenon plasma arc light", 119, pp.610~616 (2001)
- "An in vivo study to compare a plasma arc light and a conventional quartz halogen curing light in orthodontic bonding", 26, pp.573~577 (2004)
- "Blue light emitting diodes another method of light curing?", 178, pp.169~ (1995)
- "Newly developed curing unit using blue light-emitting diodes", 34, pp.49~53 (1998)
- "In-vitro pulp chamber temperature rise during composite resin polymerization with various light-curing sources", 15, pp.275~281 (1999)
- "Comparisons of different debonding techniques for ceramic brackets: an in vitro study. Part I. Background and methods", 98, pp.145~153 (1990)
- "The effect of post-cure heating on residual, unreacted monomer in a commercial resin composite", 16, pp.244~247 (2000)
- "Incorporation of bacterial inhibitor into resin composite", 73, pp.1437~1443 (1994)
- "Residual monomer", additive release and variability in cytotoxicity of light-curing glass-ionomer cements and compomers, 1999, pp.78, 724~
- "A review of direct orthodontic bonding", 2, pp.171~178 (1975)
- "Failure at the dental adhesive-etched enamel interface", 1, pp.265~284 (1974)
- "Enamel alterations from bracket bonding and debonding: a study with the scanning electron microscope", 79, pp.500~522 (1981)
- "An ex vivo investigation into the use of a plasma arc lamp when using a visible light-cured composite and a resin-modified glass poly(alkenoate) cement in orthodontic bonding", 28, pp.237~244 (2001)
- "Effects of conventional and high-intensity light-curing on enamel shear bond strength of composite resin and resin-modified glass-ionomer", 119, pp.30~35 (2001)
- "A comparison of shear bond strengths of orthodontic brackets using various light sources, light guides, and cure times", 121, pp.510~515 (2002)
- "Elution of TEGDMA and BisGMA from a resin and a resin composite cured with halogen or plasma light", 108, pp.341~345 (2000)
- "A study of bond strength between light- and self-cured orthodontic resin", 101, pp.350~354 (1992)
- "Evaluation of a new light-cured orthodontic bonding adhesive", 114, pp.80~87 (1998)
- "Evaluation of a new curing light on the shear bond strength of orthodontic brackets", 73, pp.431~435 (2003)
- "Effectiveness of composite resin polymerization using light-emitting diodes(LEDs) or halogen-based light-curing units", 18, pp.266~270 (2004)
- "Curing efficiency of various types of light-curing units", 112, pp.89~94 (2004)
- "Thermal emission and curing efficiency of LED and halogen curing lights", 30, pp.257~264 (2005)
- "Shear bond strength of orthodontic brackets bonded with light-emitting diode curing units at various polymerization times", 125, pp.337~341 (2004)
- "Pulp response to externally applied heat", 19, pp.515~530 (1965)
- "Vital microscopy of the pulp in the rat incisor. VII. Reactions to silicate cements", 63, pp.178~186 (1967)
- "In vitro temperature change at the dentin", pulpal interface by using conventional visible light versus argon laser, 2000, pp.26, 386~397
- "Plasma arc curing lights for orthodontic bonding", 122, pp.643~648 (2002)
- "Plasma arc curing of ceramic brackets: an evaluation of shear bond strength and debonding characteristics", 124, pp.309~315 (2003)
- "Depth of cure and marginal adaptation to dentin of xenon lamp polymerized resin composites", 26, pp.585~590 (2001)
- "Clinical trials with crystal growth conditioning as an alternative to acid-etch enamel pretreatment", 85, pp.333~340 (1984)
- "Residual debris and bond strength: is there a relationship?", 94, pp.222~230 (1988)
- "The effect of different methods of bracket removal on the amount of residual adhesive", 93, pp.196~200 (1988)
- "Bond strengths and remnant adhesive resin on debonding for orthodontic bonding techniques", 108, pp.302~307 (1995)
- "Methods of debonding ceramic brackets", 19, pp.233~237 (1992)