Reevaluation of failure criteria location and novel improvement of 1/4 PCCV high fidelity simulation model under material uncertainty quantifications
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Reactor containment buildings serve as the last barrier to prevent radioactive leakage due to accidents and their safety is crucial in overpressurization conditions. Thus, the Regulatory Guide (RG) 1.216 has mentioned the global strain as one of failure criteria in the free-field for cylindrical prestressed concrete containment vessels (PCCV) subject to internal pressure. However, there is a limit that RG 1.216 shows the free-field without the specific locations of failure criteria and also the global strain corresponding to only azimuth 135 has been mentioned in NUREG/CR-6685, regardless of the elevations of the structure. Therefore, in order to reevaluate the failure criteria of the 1:4 scaled PCCV, the high fidelity simulation model based on the experimental test was significantly validated in this study, and it was interesting to find that the experimental and numerical result was very close to each other. In addition, for the consideration of the material uncertainties, the Latin hypercube method was used as a statistical approach. Consequently, it was revealed that the radial displacements of various azimuth area such as 120, 135, 150, 180 and 210 at elevations 4680 mm and 6,200 mm can represent as the global deformation at the free-field, obtained from the statistical approach.
Abstract
Reactor containment buildings serve as the last barrier to prevent radioactive leakage due to accidents and their safety is crucial in overpressurization conditions. Thus, the Regulatory Guide (RG) 1.216 has mentioned the global strain as one of failure criteria in the free-field for cylindrical prestressed concrete containment vessels (PCCV) subject to internal pressure. However, there is a limit that RG 1.216 shows the free-field without the specific locations of failure criteria and also the global strain corresponding to only azimuth 135 has been mentioned in NUREG/CR-6685, regardless of the elevations of the structure. Therefore, in order to reevaluate the failure criteria of the 1:4 scaled PCCV, the high fidelity simulation model based on the experimental test was significantly validated in this study, and it was interesting to find that the experimental and numerical result was very close to each other. In addition, for the consideration of the material uncertainties, the Latin hypercube method was used as a statistical approach. Consequently, it was revealed that the radial displacements of various azimuth area such as 120, 135, 150, 180 and 210 at elevations 4680 mm and 6,200 mm can represent as the global deformation at the free-field, obtained from the statistical approach.
참고문헌 (25)
- Pretest Analysis of a 1:4-scale Prestressed Concrete Containment Vessel Model, "R.A. Dameron", U.S. Nuclear Regulatory Commission, ~, pp.Technical Report No. NUREG (2000), CR-6685, SAND2000-2093
- Overpressurization Test of a 1:4-scale Prestressed Concrete Containment Vessel Model, "M.F. Hessheimer", U.S. Nuclear Regulatory Commission, ~, pp.Technical Report No. NUREG (2003), CR-6810, SAND2003-0840P
- Posttest Analysis of the NUPEC, "NRC 1:4 Scale Prestressed Concrete Containment Vessel Model", R.A. Dameron, 2003, Technical Report No. NUREG[DOI]
- Regulatory Guide 1.216, Containment Structural Integrity Evaluation for Internal Pressure Loadings above Design Basis Pressure, , U.S. Nuclear Regulatory Commission, ~
- S. Alhanaee, "Ultimate pressure capacity of nuclear reactor containment building under unaged and aged conditions", Nucl. Eng. Des, 335, pp.128~139 (2018)
- I. Tavakkoli, "Finite element modelling of a nuclear containment structure subjected to high internal pressure", Int. J. Pres. Ves. Pip, 153, pp.59~69 (2017)
- H. T. Hu, "Ultimate analysis of PWR prestressed concrete containment subjected to internal pressure", Int. J. Pres. Ves. Pip, 83(3), pp.161~167 (2006)
- H. T. Hu, "Ultimate analysis of PWR prestressed concrete containment under long-term prestressing loss", Ann. Nucl. Energy, 87, pp.500~510 (2016)
- S. Jin, "Fragility analysis of prestressed concrete containment under severe accident condition", Ann. Nucl. Energy, 131, pp.242~256 (2019)
- Z. Li, "Fragility analysis and probabilistic safety evaluation of the nuclear containment structure under different prestressing loss conditions", Ann. Nucl. Energy, 167, pp.108862~ (2022)
- Y. P. Liang, "Probabilistic safety assessment of nuclear containment vessel under internal pressure considering spatial variability of material properties", Int. J. Pres. Ves. Pip, 200, pp.104813~
- X. Ren, "Fragility analysis of a prestressed concrete containment vessel subjected to internal pressure via the probability density evolution method", Nucl. Eng. Des, 390, pp.111709~ (2022)
- CAE Ver, "ABAQUS", pp.2021, ABAQUS
- CAE User's Manual, "ABAQUS", pp.2021, ABAQUS
- E. Hognestad, "A Study on Combined Bending and Axial Load in Reinforced Concrete Members" (1951), University of Illinois at Urbana Campaign
- H. T. Nguyen, "Finite element modeling of push-out tests for large stud shear connectors", J. Constr. Steel Res, 65(10), pp.1909~1920 (2009)
- J. Izumo, "Analy. model RC panel elem.subjected to inplane forces", 12, pp.155~181 (1989)
- Standard Specifications for Concrete Structures-Materials and Constructions, "JSCE", Concrete Committee of Japan Society of Civil Engineers, ~, pp.JSCE guideline for concrete No. 16
- A Study on the Nonlinear Analysis of a 1, "4Scale Prestressed Concrete Containment Vessel Model", H.P. Lee, 2004, KAERI[DOI]
- S. Syed, "Seismic fragility of RC shear walls in nuclear power plant part 1 : characterization of uncertainty in concrete constitutive model", Nucl. Eng. Des, 295(15), pp.576~586 (2015)
- L. Chu, "Application of Latin hypercube sampling based kriging surrogate models in reliability assessment", Sci. J. Appl. Math. Stat, 3(6), pp.263~274 (2015)
- A. Olsson, "Latin hypercube sampling for stochastic finite element analysis", J. Eng. Mech, 128(1), pp.121~125 (2002)
- I. H. Yang, "Uncertainty analysis of concrete structures using modified Latin hypercube sampling method", Inter. J. Concrete Struc. Mater, 18(2E), pp.89~95 (2006)
- M. D. McKay, "A comparison of three methods for selecting values of input variables in the analysis of output from a computer code", Technometrics, 21(2), pp.55~61 (1979)
- M. Stein, "Large sample properties of simulations using Latin hypercube sampling", Technomatrics, 29(2), pp.143~151 (1987)