Power density of various light curing units through resin inlays with modified layer thickness
2
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
Objectives: The purpose of this study was to enhance curing light penetration through resin inlays by modifying the thicknesses of the dentin, enamel, and translucent layers. Materials and Methods: To investigate the layer dominantly affecting the power density of light curing units, resin wafers of each layer with 0.5 mm thickness were prepared and power density through resin wafers was measured with a dental radiometer (Cure Rite, Kerr). The dentin layer, which had the dominant effect on power density reduction, was decreased in thickness from 0.5 to 0.1 mm while thickness of the enamel layer was kept unchanged at 0.5 mm and thickness of the translucent layer was increased from 0.5 to 0.9 mm and vice versa, in order to maintain the total thickness of 1.5 mm of the resin inlay. Power density of various light curing units through resin inlays was measured. Results: Power density measured through 0.5 mm resin wafers decreased more significantly with the dentin layer than with the enamel and translucent layers (p < 0.05). Power density through 1.5 mm resin inlays increased when the dentin layer thickness was reduced and the enamel or translucent layer thickness was increased. The highest power density was recorded with dentin layer thickness of 0.1 mm and increased translucent layer thickness in all light curing units. Conclusions: To enhance the power density through resin inlays, reducing the dentin layer thickness and increasing the translucent layer thickness would be recommendable when fabricating resin inlays.
Abstract
Objectives: The purpose of this study was to enhance curing light penetration through resin inlays by modifying the thicknesses of the dentin, enamel, and translucent layers. Materials and Methods: To investigate the layer dominantly affecting the power density of light curing units, resin wafers of each layer with 0.5 mm thickness were prepared and power density through resin wafers was measured with a dental radiometer (Cure Rite, Kerr). The dentin layer, which had the dominant effect on power density reduction, was decreased in thickness from 0.5 to 0.1 mm while thickness of the enamel layer was kept unchanged at 0.5 mm and thickness of the translucent layer was increased from 0.5 to 0.9 mm and vice versa, in order to maintain the total thickness of 1.5 mm of the resin inlay. Power density of various light curing units through resin inlays was measured. Results: Power density measured through 0.5 mm resin wafers decreased more significantly with the dentin layer than with the enamel and translucent layers (p < 0.05). Power density through 1.5 mm resin inlays increased when the dentin layer thickness was reduced and the enamel or translucent layer thickness was increased. The highest power density was recorded with dentin layer thickness of 0.1 mm and increased translucent layer thickness in all light curing units. Conclusions: To enhance the power density through resin inlays, reducing the dentin layer thickness and increasing the translucent layer thickness would be recommendable when fabricating resin inlays.
참고문헌 (24)
- Sheth PJ, "Comparative evaluation of three resin inlay techniques: microleakage studies", Quintessence Int, 20, pp.831~836 (1989)
- Bausch JR, "Clinical significance of polymerization shrinkage of composite resins", J Prosthet Dent, 48, pp.59~67 (1982)
- Eick JD, "Polymerization shrinkage of posterior composite resins and its possible influence on postoperative sensitivity", Quintessence Int, 17, pp.103~111 (1986)
- Robinson PB, "Comparison of microleakage in direct and indirect composite resin restorations in vitro", Oper Dent, 12, pp.113~116 (1987)
- Roberson TM, "Sturdevant’s art & science of operative dentistry 4th ed", pp.580~ (2002), Mosby Inc
- el-Mowafy O, "The use of resin cements in restorative dentistry to overcome retention problems", J Can Dent Assoc, 67, pp.97~102 (2001)
- Sorensen JA, "Porcelain-composite interface microleakage with various porcelain surface treatments", Dent Mater, 7, pp.118~123 (1991)
- Jensen ME, "Etched-porcelain resinbonded full-veneer crowns: in vitro fracture resistance", Compendium, 10, pp.336~338 (1989)
- Krämer N, "Adhesive luting of indirect restorations", Am J Dent, 13, pp.60~76 (2000)
- el-Badrawy WA, "Chemical versus dual curing of resin inlay cements", J Prosthet Dent, 73, pp.515~524 (1995)
- Hasegawa EA, "Hardening of dualcured cements under composite resin inlays", J Prosthet Dent, 66, pp.187~192 (1991)
- Chan KC, "Curing light-activated composite cement through porcelain", J Dent Res, 68, pp.476~480 (1989)
- Rasetto FH, "Effect of light source and time on the polymerization of resin cement through ceramic veneers", J Prosthodont, 10, pp.133~139 (2001)
- Rueggeberg FA, "Effect of light-tip distance on polymerization of resin composite", Int J Prosthodont, 6, pp.364~370 (1993)
- 장훈상, "감염 조절용 차단막의 두께가 광중합기의 중합광에 미치는 영향", Restorative Dentistry and Endodontics, 35(5), pp.368~373 (2010), 대한치과보존학회
- Blackman R, "Influence of ceramic thickness on the polymerization of light-cured resin cement", J Prosthet Dent, 63, pp.295~300 (1990)
- Prati C, "Effect of air, dentin and resin-based composite thickness on light intensity reduction", Am J Dent, 12, pp.231~234 (1999)
- dos Santos GB, "Light transmission on dental resin composites", Dent Mater, 24, pp.571~576 (2008)
- Kim SS, "The microhardness and the degree of conversion of light cured composite resin and dual cured resin cements under porcelain inlay", J Korean Acad Conserv Dent, 25, pp.17~40 (2000)
- 장훈상, "직접수복용 레진과 기공용 레진으로 제작한 레진 인레이를 투과한 광중합기의 광강도", Restorative Dentistry and Endodontics, 35(5), pp.353~358 (2010), 대한치과보존학회
- Taira M, "Studies on optical properties of two commercial visible-light-cured composite resins by diffuse reflectance measurements", J Oral Rehabil, 26, pp.329~337 (1999)
- 장훈상, "광중합기 사용 시의 감염 조절", Restorative Dentistry and Endodontics, 35(4), pp.235~237 (2010), 대한치과보존학회
- Rueggeberg FA, "Effect of light intensity and exposure duration on cure of resin composite", Oper Dent, 19, pp.26~32 (1994)
- Hofmann N, "Effect of irradiation type(LED or QTH) on photo-activated composite shrinkagestrain kinetics, temperature rise, and hardness", Eur JOral Sci, 110, pp.471~479 (2002)