Effects of air-abrasion pressure on the resin bond strength to zirconia: a combined cyclic loading and thermocycling aging study
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Objectives: To determine the combined effect of fatigue cyclic loading and thermocycling (CLTC) on the shear bond strength (SBS) of a resin cement to zirconia surfaces that were previously air-abraded with aluminum oxide (Al2O3) particles at different pressures. Materials and Methods: Seventy-two cuboid zirconia specimens were prepared and randomly assigned to 3 groups according to the air-abrasion pressures (1, 2, and 2.8 bar), and each group was further divided into 2 groups depending on aging parameters (n = 12). Panavia F 2.0 was placed on pre-conditioned zirconia surfaces, and SBS testing was performed either after 24 hours or 10,000 fatigue cycles (cyclic loading) and 5,000 thermocycles. Non-contact profilometry was used to measure surface roughness. Failure modes were evaluated under optical and scanning electron microscopy. The data were analyzed using 2-way analysis of variance and χ2 tests (α = 0.05). Results: The 2.8 bar group showed significantly higher surface roughness compared to the 1 bar group (p < 0.05). The interaction between pressure and time/cycling was not significant on SBS, and pressure did not have a significant effect either. SBS was significantly higher (p = 0.006) for 24 hours storage compared to CLTC. The 2 bar-CLTC group presented significantly higher percentage of pre-test failure during fatigue compared to the other groups. Mixed-failure mode was more frequent than adhesive failure. Conclusions: CLTC significantly decreased the SBS values regardless of the air-abrasion pressure used.
Abstract
Objectives: To determine the combined effect of fatigue cyclic loading and thermocycling (CLTC) on the shear bond strength (SBS) of a resin cement to zirconia surfaces that were previously air-abraded with aluminum oxide (Al2O3) particles at different pressures. Materials and Methods: Seventy-two cuboid zirconia specimens were prepared and randomly assigned to 3 groups according to the air-abrasion pressures (1, 2, and 2.8 bar), and each group was further divided into 2 groups depending on aging parameters (n = 12). Panavia F 2.0 was placed on pre-conditioned zirconia surfaces, and SBS testing was performed either after 24 hours or 10,000 fatigue cycles (cyclic loading) and 5,000 thermocycles. Non-contact profilometry was used to measure surface roughness. Failure modes were evaluated under optical and scanning electron microscopy. The data were analyzed using 2-way analysis of variance and χ2 tests (α = 0.05). Results: The 2.8 bar group showed significantly higher surface roughness compared to the 1 bar group (p < 0.05). The interaction between pressure and time/cycling was not significant on SBS, and pressure did not have a significant effect either. SBS was significantly higher (p = 0.006) for 24 hours storage compared to CLTC. The 2 bar-CLTC group presented significantly higher percentage of pre-test failure during fatigue compared to the other groups. Mixed-failure mode was more frequent than adhesive failure. Conclusions: CLTC significantly decreased the SBS values regardless of the air-abrasion pressure used.
참고문헌 (33)
- Lazar DR, "Y-TZP ceramic processing from coprecipitated powders: a comparative study with three commercial dental ceramics", Dent Mater, 24, pp.1676~1685 (2008)
- Luangruangrong P, "Influence of full-contour zirconia surface roughness on wear of glass-ceramics", J Prosthodont, 23, pp.198~205 (2014)
- Denry I, "Emerging ceramic-based materials for dentistry", J Dent Res, 93, pp.1235~1242 (2014)
- Lawson NC, "Dental ceramics: a current review", Compend Contin Educ Dent, 35, pp.161~166 (2014)
- Wang H, "Strength influencing variables on CAD", CAM zirconia frameworks, 2008, pp.24, 633~638
- Lohbauer U, "Hydroxylation of dental zirconia surfaces: characterization and bonding potential", J Biomed Mater Res B Appl Biomater, 87, pp.461~467 (2008)
- Wegner SM, "Long-term resin bond strength to zirconia ceramic", J Adhes Dent, 2, pp.139~147 (2000)
- Blatz MB, "Resin-ceramic bonding: a review of the literature", J Prosthet Dent, 89, pp.268~274 (2003)
- Hummel M, "Durability of the resin bond strength to the alumina ceramic Procera", Dent Mater, 20, pp.498~508 (2004)
- Friederich R, "Resin bond strength to densely sintered alumina ceramic", Int J Prosthodont, 15, pp.333~338 (2002)
- Kern M, "Bonding to oxide ceramics—laboratory testing versus clinical outcome", Dent Mater, 31, pp.8~14 (2015)
- Thompson JY, "Adhesion", cementation to zirconia and other non-silicate ceramics: where are we now?, 2011, pp.27, 71~82
- 서덕규, "Zirconia surface treatment for successful bonding", Restorative Dentistry and Endodontics, 39(4), pp.333~333 (2014), 대한치과보존학회
- Bottino MA, "Bonding of Y-TZP to dentin: effects of Y-TZP surface conditioning, resin cement type, and aging", Oper Dent, 39, pp.291~300 (2014)
- Inokoshi M, "Meta-analysis of bonding effectiveness to zirconia ceramics", J Dent Res, 93, pp.329~334 (2014)
- de Souza G, "The use of MDP-based materials for bonding to zirconia", J Prosthet Dent, 112, pp.895~902 (2014)
- Blatz MB, "In vitro evaluation of shear bond strengths of resin to densely-sintered high-purity zirconium-oxide ceramic after long-term storage and thermal cycling", J Prosthet Dent, 91, pp.356~362 (2004)
- Özcan M, "Adhesion to zirconia used for dental restorations: a systematic review and meta-analysis", J Adhes Dent, 17, pp.7~26 (2015)
- Özcan M, "Effect of air-particle abrasion protocols on the biaxial flexural strength, surface characteristics and phase transformation of zirconia after cyclic loading", J Mech Behav Biomed Mater, 20, pp.19~28 (2013)
- Kern M, "Surface conditioning influences zirconia ceramic bonding", J Dent Res, 88, pp.817~822 (2009)
- Aurélio IL, "Does air particle abrasion affect the flexural strength and phase transformation of Y-TZP? A systematic review and meta-analysis", Dent Mater, 32, pp.827~845 (2016)
- Barkmeier WW, "Fatigue limits of enamel bonds with moist and dry techniques", Dent Mater, 25, pp.1527~1531 (2009)
- Wegner SM, "Effect of different artificial aging conditions on ceramic-composite bond strength", Int J Prosthodont, 15, pp.267~272 (2002)
- Williamson RT, "The effect of fatigue on the shear bond strength of resin bonded to porcelain", J Prosthodont, 2, pp.115~119 (1993)
- Re D, "Early bond strength to low-pressure sandblasted zirconia: evaluation of a self-adhesive cement", Eur J Esthet Dent, 7, pp.164~175 (2012)
- Zhang Y, "Damage accumulation and fatigue life of particle-abraded ceramics", Int J Prosthodont, 19, pp.442~448 (2006)
- Zhang Y, "Effect of sandblasting on the long-term performance of dental ceramics", J Biomed Mater Res B Appl Biomater, 71, pp.381~386 (2004)
- Özcan M, "Comparison of resin cement adhesion to Y-TZP ceramic following manufacturers' instructions of the cements only", Clin Oral Investig, 12, pp.279~282 (2008)
- Nishigori A, "Influence of zirconia surface treatment on veneering porcelain shear bond strength after cyclic loading", J Prosthet Dent, 112, pp.1392~1398 (2014)
- Kern M, "Bonding to zirconia ceramic: adhesion methods and their durability", Dent Mater, 14, pp.64~71 (1998)
- Chang JC, "Bond strength of composite to alloy treated with bonding systems", J Prosthodont, 2, pp.110~114 (1993)
- Chen L, "Bonding of primed zirconia ceramics: evidence of chemical bonding and improved bond strengths", Am J Dent, 25, pp.103~108 (2012)
- Nemli SK, "Effect of fatigue on fracture toughness and phase transformation of Y-TZP ceramics by X-ray diffraction and Raman spectroscopy", J Biomed Mater Res B Appl Biomater, 100, pp.416~424 (2012)