A Numerical study for the efficacy of flow injection on the diminution of rudder cavitation
2
조회
0
다운로드
4
인용
0
참고문헌
키워드
초록
The complete avoidance of cavitation, as a result of gap flow between the fixed and movable portion of a horn type rudder system, is difficult. To reduce gap flow, it is a common practice to attach a half round prismatic bar that protrudes beyond the concave surface of the horn facing the gap and laid along the centerplane of the rudder. However the employment of such a device does not always yield satisfactory results. Previously, the authors have shown that a pair of blocking bars, attached on the convex surface of the movable portion, better enhance the blocking ability of gap flow to that of a single centre bar installed on the concave surface. This also circumvents difficulties that might occur in practical applications. In the present study, a series of numerical computations show that flow injected into the gap of a rudder may also block the flow within, without employment of any physical devices, such as a half circular bar. This study also shows that the combination of flow injection and blocking bars may result in the synergic augmentation of blocking efficiency of gap flow, as demonstrated in computations for a three dimensional rudder system.
Abstract
The complete avoidance of cavitation, as a result of gap flow between the fixed and movable portion of a horn type rudder system, is difficult. To reduce gap flow, it is a common practice to attach a half round prismatic bar that protrudes beyond the concave surface of the horn facing the gap and laid along the centerplane of the rudder. However the employment of such a device does not always yield satisfactory results. Previously, the authors have shown that a pair of blocking bars, attached on the convex surface of the movable portion, better enhance the blocking ability of gap flow to that of a single centre bar installed on the concave surface. This also circumvents difficulties that might occur in practical applications. In the present study, a series of numerical computations show that flow injected into the gap of a rudder may also block the flow within, without employment of any physical devices, such as a half circular bar. This study also shows that the combination of flow injection and blocking bars may result in the synergic augmentation of blocking efficiency of gap flow, as demonstrated in computations for a three dimensional rudder system.
참고문헌 (11)
- Boo, K.T, "Numerical Simulation for the Rudder in order to Control the Cavitation Phenomena", Journal of Ship and Ocean Technology, 8(1), pp.42~50 (2004)
- 정현주, "Unsteady flow around a two-dimensional section of a vertical axis turbine for tidal stream energy conversion", International Journal of Naval Architecture and Ocean Engineering, 1(2), pp.64~69 (2009), 대한조선학회
- 김성표, "혼-타의 간극 캐비테이션 침식 저감을 위한 실험적 연구", 대한조선학회 논문집, 43(5), pp.578~585 (2006), 대한조선학회
- 김문찬, "유전자 알고리즘을 이용한 컨테이너선을 위한 침식예방용 최적방향타 단면 설계", 대한조선학회 논문집, 45(4), pp.403~410 (2008), 대한조선학회
- 오정근, "차단 봉이 혼과 타판 사이에 대칭으로 배치된타의 틈새유동 수치해석", 대한조선학회 논문집, 46(5), pp.460~470 (2009), 대한조선학회
- 백부근, "프로펠러 및 선미반류에 의해 영향을 받는 혼-타의 캐비테이션 관찰 및 간극 유동에 대한 가시화 연구", 대한조선학회 논문집, 45(3), pp.238~246 (2008), 대한조선학회
- Rhee, S.H, "A Suggestion of Gap Flow Control Devices for the Suppression of Rudder Cavitation", Journal of Marine Science and Technology, 13(4), pp.356~370 (2008)
- Rhee, S.H, "Rudder Gap Cavitation: Fundamental Understanding and Its Suppression Devices", International Journal of Heat and Fluid Flow, available online (2010)
- 서대원, "제트 노즐의 배치가 콴다 날개의 성능에 미치는 영향", 대한조선학회 논문집, 45(6), pp.569~578 (2008), 대한조선학회
- 서대원, "유체 공급장치를 활용한 간극유동 제어에 관한 수치적 연구", 대한조선학회 논문집, 46(6), pp.578~586 (2009), 대한조선학회
- Shen, Y.T, "A Twisted Rudder for Reduced Cavitation", Journal of Ship Research, 41(4), pp.260~272 (1997)