차량용 IHX에서 핀 특성이 난류 유동에 미치는 영향
Influence of Fin Characteristics on the Turbulent Flow in IHX for a Vehicle
1
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
It is known that the cooling performance can be improved about 5~12% and the COP (Coefficient of Performance) can be improved about 10~15% when the IHX (Internal Heat Exchanger) was applied in a vehicle. Thus, the aim of this study was to observe the influence of the fins shape on the turbulence flow and turbulence kinetic energy gradient in IHX. All the applied parameters of the fin such as rotation angle, spacing ratio, height ratio and mass flow rate are changed. The governing equations for the flow motion simulation were applied to continuity equation and Navier-Stokes equation, and the turbulence model was applied by the Shear Stress Transport(SST) model, which has the advantage of turbulence simulation. As the rotation angles ofthe front and back fins were increased, the difference in the maximum turbulent kinetic energy gradient between fins was reduced. As the inlet flow mass increased, the turbulent kinetic energy difference between front and back fins were increased. The turbulence area tended to increase with increasing fin height ratio.
Abstract
It is known that the cooling performance can be improved about 5~12% and the COP (Coefficient of Performance) can be improved about 10~15% when the IHX (Internal Heat Exchanger) was applied in a vehicle. Thus, the aim of this study was to observe the influence of the fins shape on the turbulence flow and turbulence kinetic energy gradient in IHX. All the applied parameters of the fin such as rotation angle, spacing ratio, height ratio and mass flow rate are changed. The governing equations for the flow motion simulation were applied to continuity equation and Navier-Stokes equation, and the turbulence model was applied by the Shear Stress Transport(SST) model, which has the advantage of turbulence simulation. As the rotation angles ofthe front and back fins were increased, the difference in the maximum turbulent kinetic energy gradient between fins was reduced. As the inlet flow mass increased, the turbulent kinetic energy difference between front and back fins were increased. The turbulence area tended to increase with increasing fin height ratio.
참고문헌 (12)
- S. S. Moon, "Strategies to Realize 45 % Thermal Efficiency of Gasoline Engines", Auto Journal of KSAE, 38(11), pp.16~20 (2016)
- H. Y. Kang, "Effects of Variable Induction System on the Improvement of Volumetric Efficiency in a Turbocharged Diesel Engine", KSAE Annual Conference Proceedings, pp.232~238 (2006)
- 백동훈, "가솔린 직접분사엔진에서 EGR량에 따른 연비향상에 관한 연구", 한국기계기술학회지, 20(1), pp.68~74 (2018), 한국기계기술학회[DOI]
- 백동훈, "가솔린-에탄올 혼합연료를 사용하는 SI 엔진의 성능 및 NOx에 관한 연구", 한국기계기술학회지, 18(5), pp.765~770 (2016), 한국기계기술학회[DOI]
- Y. H. Ham, "Performance Variation with Length of Internal Heat Exchanger under Mobile Air-conditioner Operating Conditions using R1234yf and R134a", KSAE Annual Conference Proceedings, pp.488~492 (2015)
- J. H. Lee, "Study on Performance Prediction of Automotive Air Conditioning System applying a Double Pipe Heat Exchanger", KSAE Annual Conference Proceedings, pp.501~505 (2012)
- 곽명석, "이산화탄소 냉방운전 시 냉매충전량 및 운전조건에 따라 내부열교환기가 성능에 미치는 영향", 한국지열·수열에너지학회논문집, 8(1), pp.13~20 (2012), 한국 지열 · 수열에너지학회
- K. J. Lee, "An Experimental Study on the Evaporation Heat Transfer Characteristics of Double Pipe Heat Exchanger", KSME Annual Conference Proceedings, pp.828~832 (2012)
- H. G. Cho, "Analysis of Concentric Heat Exchanger Performance for the Fin Shape on the Inner Tube", Korean Journal of Air-Conditioning and Refrigeration Engineering, pp.14~17 (2012)
- 조동현, "연료전지 냉각용 헬리컬 인서트디바이스 이중관열교환기의 열전달 성능 향상에 관한 연구", 수산해양교육연구, 27(6), pp.1872~1879 (2015), 한국수산해양교육학회
- 조동현, "연료전지용 딤플형 이중관열교환기의 열전달 성능에 관한 연구", 수산해양교육연구, 27(6), pp.1727~1733 (2015), 한국수산해양교육학회
- M. W. Kang, "Experimental Study on the Performance Characteristics of Mobile Air-Conditioning System according to IHX", KSAE Annual Conference Proceedings, pp.493~497 (2015)