마이크로버블 발생을 위한 벤추리 노즐 형상 연구
Experimental Study of Venturi Nozzle Geometry for Microbubble Generation
0
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
Microbubble is a part of advanced water treatment technologies, and there are several ways for microbubble generation. A strategy using Venturi (convergent-divergent) nozzle with air-suction holes has advantage of energy and time saving compared with the others. Here, we used 3D printer to make the various nozzle geometries in order to understand two-phase flow in the Venturi nozzle and air-breaking mechanism. It was evaluated the effects of convergent and divergent angles independently on air-suction rate and pressure drop, and the two-phase flow (air bubbles and liquid water) were observed. The convergent angle strongly affect the air-suction rate corresponding with increase of pressure drop. Meanwhile, as the divergent angle increased, it became dominant the minor loss by sudden enlargement of flow area, so that the air-suction rate and pressure drop showed decreased.
Abstract
Microbubble is a part of advanced water treatment technologies, and there are several ways for microbubble generation. A strategy using Venturi (convergent-divergent) nozzle with air-suction holes has advantage of energy and time saving compared with the others. Here, we used 3D printer to make the various nozzle geometries in order to understand two-phase flow in the Venturi nozzle and air-breaking mechanism. It was evaluated the effects of convergent and divergent angles independently on air-suction rate and pressure drop, and the two-phase flow (air bubbles and liquid water) were observed. The convergent angle strongly affect the air-suction rate corresponding with increase of pressure drop. Meanwhile, as the divergent angle increased, it became dominant the minor loss by sudden enlargement of flow area, so that the air-suction rate and pressure drop showed decreased.
참고문헌 (13)
- M. Takahashi, "Free-radical generation from collapsing microbubbles in the absence of a dynamic stimulus", The Journal of Physical Chemistry B, 111(6), pp.1343~1347 (2007)
- K. Terasaka, "Development of microbubble aerator for waste water treatment using aerobic activated sludge", Chemical engineering science, 66(14), pp.3172~3179 (2011)
- A. Agarwal, "Principle and applications of microbubble and nanobubble technology for water treatment", Chemosphere, 84(9), pp.1175~1180 (2011)
- H. Ikeura, "Removal of residual pesticide, fenitrothion, in vegetables by using ozone microbubbles generated by different methods", Journal of Food Engineering, 103(3), pp.345~349 (2011)
- M. Sadatomi, "Micro-bubble generation rate and bubble dissolution rate into water by a simple multi-fluid mixer with orifice and porous tube", Experimental Thermal and Fluid Science, 41, pp.23~30 (2012)
- J. Yin, "Experimental study on the bubble generation characteristics for an venturi type bubble generator", International Journal of Heat and Mass Transfer, 91, pp.218~224 (2015)
- J. Huang, "A visualized study of bubble breakup in small rectangular Venturi channels", Experimental and Computational Multiphase Flow, pp.1~9 (2019)
- M. Sadatomi, "Performance of a new micro-bubble generator with a spherical body in a flowing water tube", Experimental Thermal and Fluid Science, 29(5), pp.615~623 (2005)
- N. M. Nouri, "An experimental study on the influence of fluid flow pattern on microbubble generation", Forschung im Ingenieurwesen, 72(4), pp.233~ (2008)
- C. H. Lee, "Experimental investigation of microbubble generation in the venturi nozzle", International Journal of Heat and Mass Transfer, 136, pp.1127~1138 (2019)
- 원대희, "이종재료를 사용한 3D 프린터용 히팅블록 개발", 한국기계기술학회지, 19(2), pp.249~254 (2017), 한국기계기술학회[DOI]
- E. M. Sparrow, "Flow separation in a diverging conical duct : Effect of Reynolds number and divergence angle", International Journal of Heat and Mass Transfer, 52(13-14), pp.3079~3083 (2009)
- J. M. Mandhane, "A flow pattern map for gas—liquid flow in horizontal pipes", International Journal of Multiphase Flow, 1(4), pp.537~553 (1974)