시뮬레이션 분석을 이용한 사출성형 중 사출구간에서의 금형 변형량 예측 및 실험적 검증에 관한 연구
A Study on the Experimental Verification and Prediction of Mold Deformation at Injection Stage during Injection Molding through Simulation Analysis
2
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
In this study, in order of to reflect the mold deformation in the injection molding process to design of mold, the mold deformation was analyzed by performing flow and structural analysis. The 5 inch LGP(light guide plate) mold, platen and tie bar were modeled and applied to the analysis. The result of melt pressure from flow analysis was extracted for use as boundary conditions acting on the mold surface in the structural analysis. In order to evaluate the accuracy of simulation analysis results, injection molding was performed under the process conditions of simulation. As a results, the mold deformation during injection molding tends to be similar that of injection pressure, and it is confirmed that it shows the behavior and properties of melt resins. Compared with the simulation and experiment, the error of the maximum mold deformation in the injection phase was 4.20%.
Abstract
In this study, in order of to reflect the mold deformation in the injection molding process to design of mold, the mold deformation was analyzed by performing flow and structural analysis. The 5 inch LGP(light guide plate) mold, platen and tie bar were modeled and applied to the analysis. The result of melt pressure from flow analysis was extracted for use as boundary conditions acting on the mold surface in the structural analysis. In order to evaluate the accuracy of simulation analysis results, injection molding was performed under the process conditions of simulation. As a results, the mold deformation during injection molding tends to be similar that of injection pressure, and it is confirmed that it shows the behavior and properties of melt resins. Compared with the simulation and experiment, the error of the maximum mold deformation in the injection phase was 4.20%.
참고문헌 (16)
- 김경모, "Mahalanobis Taguchi System을 이용한 사출 공정의 최적설계", 한국기계가공학회지, 16(1), pp.1~8 (2017), 한국기계가공학회[DOI]
- 류미라, "다구찌 기법을 이용한 베벨기어 사출금형의 최적화", 한국기계기술학회지, 12(3), pp.91~96 (2010), 한국기계기술학회[DOI]
- 류미라, "회귀분석법을 이용한 사출금형의 수축률 분석에 관한 연구", 한국기계기술학회지, 13(3), pp.113~118 (2011), 한국기계기술학회[DOI]
- Carpenter, B., "Effect of Machine Compliance on Mold Deflection During Injection and Packing of Thermoplastic Parts", Polym. Eng. Sci., 46(7), pp.844~852 (2006)
- Huang, C. C., "An effective approach to measuring real-time mold deflection during injection molding", J. Polym. Eng, 31(8-9), pp.549~560 (2011)
- 정태성, "초박형 도광판의 고속 사출성형에서 충전 불균형에 대한 연구", 폴리머, 41(1), pp.30~38 (2017), 한국고분자학회[DOI]
- 정현석, "형체력에 따른 사출성형기 플렉스링크의 특성 분석", 한국정밀공학회지, 31(2), pp.165~170 (2014), 한국정밀공학회
- Bin, R., "Structural Scheme Optimization Design for the Stationary Platen of a Precision Plastic Injection Molding Machine", Chin. J. Mech. Eng, 27(4), pp.714~721 (2014)
- Kim, J., "Finite element analysis and modeling of structure with bolted joints", Appl. Math. Modell, 31(5), pp.895~911 (2007)
- Montgomery, J., "Methods for modeling bolts in the bolted joint", ANSYS user’s Conference 2002 (2002)
- 정현수, "볼트결합 구조의 부재 강성 연구", 한국생산제조학회지, 27(3), pp.167~174 (2018), 한국생산제조학회[DOI]
- Hong, S. K., "Correlation between thermal contact resistance and filling behavior of a polymer melt into multiscale cavities in injection molding", Int. J. Heat Mass Transfer, 87, pp.222~236 (2015)
- The effect of heat transfer coefficients and thermal conductivity on polymer processing simulation, "Dawson, A.", National Physical Laboratory, ~, pp.Repot MAT 17 (2008)
- Yu. C. J., "Thermal Contact Resistance in Injection Molding", 30(24), pp.1599~1606 (1990)
- Lee, H. S., "Frozen Layer Effect on Internal Cavity Pressure during Injection Molding", Proc. Korea Soc. Precis. Eng, pp.474~479 (2005)
- Li, H., "Study of the structural characteristics of mold for precise injection molding", Adv. Mater. Res, 291-294, pp.610~613 (2011)