사출성형조건이 용융수지의 유동선단에 미치는 영향의 수치해석적 연구
A Numerical Study on the Effect of Injection Molding Conditions on The Melt Front
4
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
In this study, we used a numerical analysis program to study the molding conditions that affect the flow rate at the time of injection, using a spiral mold, which is mainly used for the evaluation of the flow rate of plastic resin. The mold temperature, melt temperature, and flow rate are composed of experimental factors. The three plastic forming factors were divided into five to six levels each. Since then, changes in the flow rate temperature were analyzed as the level of each forming factor increased. Experiments showed that all three forming factors increased the filling length of the spiral mold and the temperature of the flow front by a total of 34.53°C, melt temperatures increased the temperature of the flow front by a total of 34.53°C, the temperature increased by the flow rate was 23.5°C, and the temperature increased by the mold temperature was 1.99°C. It was shown that the melt temperature was the largest, followed by the flow rate and mold temperature. It was also possible to check the effect of plastic forming factors on the speed of the flow front.
Abstract
In this study, we used a numerical analysis program to study the molding conditions that affect the flow rate at the time of injection, using a spiral mold, which is mainly used for the evaluation of the flow rate of plastic resin. The mold temperature, melt temperature, and flow rate are composed of experimental factors. The three plastic forming factors were divided into five to six levels each. Since then, changes in the flow rate temperature were analyzed as the level of each forming factor increased. Experiments showed that all three forming factors increased the filling length of the spiral mold and the temperature of the flow front by a total of 34.53°C, melt temperatures increased the temperature of the flow front by a total of 34.53°C, the temperature increased by the flow rate was 23.5°C, and the temperature increased by the mold temperature was 1.99°C. It was shown that the melt temperature was the largest, followed by the flow rate and mold temperature. It was also possible to check the effect of plastic forming factors on the speed of the flow front.
참고문헌 (9)
- 한성렬, "사출성형해석 연구를 이용한 게이트 밸런스 계산식의 검증", Design & Manufacturing, 12(3), pp.55~59 (2018), 한국금형공학회[DOI]
- S. M. Lee, "Forming analysis", Korea Association of Machinery Industry, 51~51 (2009)
- J. H. Lee, "A Study on the Measurement of Polymer Viscosity by Injection Molding and Application for Injection Molding Machine to Maintain Conditions", Korean Society for Precision Engineering, pp.379~379 (2017)
- 김명호, "금속사출 유동선단온도에 영향을 미치는 주요 인자들의 상호관계 및 반응표면분석", 한국생산제조학회지, 22(2), pp.248~255 (2013), 한국생산제조학회[DOI]
- I. Sandu, "Prediction of Polymer Flow Length by Coupling Finite Element Simulation with Artificial Neural Network", Mater. Plast, 57(3), pp.202~223 (2020)
- S. B. Park, "A Study on the Effects of Secondary Fluid Viscosity on the Formation of Flow Front and Residual Wall thickness in Fluid-Assisted Injection Molding", Korean Society for Precision Engineering, pp.100~100 (2014)
- S. K. Kim, "Investigation of Instabilities in flow front during micro-injection molding process", The Korean Society of Mechanical Engineers, pp.123~124 (2010)
- 한성렬, "형상 적응형 냉각채널 적용을 통한 카메라용 플라스틱 렌즈 후드의 변형 개선", 한국기계기술학회지, 21(1), pp.133~139 (2019), 한국기계기술학회[DOI]
- 정태성, "초박형 도광판의 고속 사출성형에서 충전 불균형에 대한 연구", 폴리머, 41(1), pp.30~38 (2017), 한국고분자학회[DOI]