전역 최적화 알고리즘을 이용한 파이버 레이저 용접 열원 모델 구현에 관한 연구 Part III : 용접 파워에 따른 열원파라미터의 영향도 분석
A Study for Heat Source Model for Fiber Laser Welding with Global Optimization AlgorithmPart III. Analysis of the Parameters with Welding Power
2
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
The multi-layered heat source model is a model that can cover most of existing studies and can be defined with a simple formula. Based on the methodology performed in previous studies, the welding heat source was found through experiments and FEM under the welding power conditions of three cases and the parameters of the welding heat source were analyzed according to the welding power. In this study, parameters of fiber laser welding heat source according to welding power were searched through optimization algorithm and finite element analysis, and the correlation was analyzed. It was confirmed that the concentration of the welding heat source in the 1st layer was high regardless of the welding power, and it was confirmed that the concentration of the welding heat source in the 5th layer (last layer) increased as the welding power increased. This reflects the shape of the weld bead that appears during actual fiber laser welding, and it was confirmed that this study represents the actual phenomenon.
Abstract
The multi-layered heat source model is a model that can cover most of existing studies and can be defined with a simple formula. Based on the methodology performed in previous studies, the welding heat source was found through experiments and FEM under the welding power conditions of three cases and the parameters of the welding heat source were analyzed according to the welding power. In this study, parameters of fiber laser welding heat source according to welding power were searched through optimization algorithm and finite element analysis, and the correlation was analyzed. It was confirmed that the concentration of the welding heat source in the 1st layer was high regardless of the welding power, and it was confirmed that the concentration of the welding heat source in the 5th layer (last layer) increased as the welding power increased. This reflects the shape of the weld bead that appears during actual fiber laser welding, and it was confirmed that this study represents the actual phenomenon.
참고문헌 (17)
- 표창민, "전역 최적화 알고리즘을 이용한 파이버 레이저 용접 열원 모델 구현에 관한 연구 Part I : 다층 용접 열원의 검증", 한국기계기술학회지, 23(2), pp.137~144 (2021), 한국기계기술학회[DOI]
- 표창민, "전역 최적화 알고리즘을 이용한 파이버 레이저 용접 열원 모델 구현에 관한 연구 Part II : 최적화 알고리즘의 비교", 한국기계기술학회지, 23(2), pp.226~233 (2021), 한국기계기술학회[DOI]
- J. Goldak, "A new finite element model for welding heat sources", MTB, 15, pp.299~305 (1984)
- 김재웅, "A study on an efficient prediction of welding deformation for T-joint laser welding of sandwich panel PART I : Proposal of a heat source model", International Journal of Naval Architecture and Ocean Engineering, 5(3), pp.348~363 (2013), 대한조선학회
- F. Farrokhi, "A numerical model for full and partial penetration hybrid laser welding of thick-section steels", Optics & Laser Technology, 111, pp.671~686 (2019)
- G. Xu, "Adaptive volumetric heat source models for laser beam and laser + pulsed GMAW hybrid welding processes", The International Journal of Advanced Manufacturing Technology, 57, pp.245~255 (2011)
- A. Evdokimov, "Heat source model for laser beam welding of steel-aluminum lap joints", Int J Adv Manuf Technol, 93, pp.709~716 (2017)
- T. Kik, "Heat Source Models in Numerical Simulations of Laser Welding", Materials, 13(11), pp.2653~ (2020)
- C. Pyo, "Estimation of Heat Source Model’s Parameters for GMAW with Non-linear Global Optimization—Part I : Application of Multi-island Genetic Algorithm", Metals, 10(7), pp.885~ (2020)
- W. Wang, "Multi-Objective Aerodynamic Optimization Design Method of Compressor Rotor Based on Isight", Procedia Engineering, 15, pp.3699~3703 (2011)
- D. Deng, "Numerical simulation of temperature field and residual stress in multi-pass welds in stainless steel pipe and comparison with experimental measurements", Computational Materials Science, 37(3), pp.269~277 (2006)
- Milad Moradi, "A Study on the Influence of Various Welding Sequence Schemes on the Gain in Strength of Square Hollow Section Steel T-Joint", 대한용접접합학회지, 35(4), pp.41~50 (2017), 대한용접접합학회[DOI]
- N. Saunders, "Using JMatPro to model materials properties and behavior", The journal of the minerals, metals & materials society, 55, pp.60~65 (2003)
- H. Lee, "Calculation of Material Properties with JMatPro for the Process Simulation", Proceedings of the Korean Society for Technology of Plasticity Conference, pp.142~145 (2008)
- X. Hu, "Optimization design of satellite separation systems based on Multi-Island Genetic Algorithm", Advances in Space Research, 53(5), pp.870~876 (2014)
- Z. Wang, "State-of-Health Estimation for Lithium-Ion Batteries Based on the Multi-Island Genetic Algorithm and the Gaussian Process Regression", IEEE Access, 5, pp.21286~21295 (2017)
- D. J. Zhao, "Optimization of Suction Control on an Airfoil Using Multi-island Genetic Algorithm", Procedia Engineering, 99, pp.696~702 (2015)