마퍼의 메인 프레임에 대한 최적화 설계 인자의 결정
Decision of Optimal Design Parameters for Main Frame in a Mopper
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
This study is concerned about the optimal design of the main frame in a moper. Mopper is widely used for cleaning in the fields such as airport, subway, train station, large shopping mall, department store, hospital, government buildings, school, industrial building floor, etc. Especially, main frame in mopper are stressed by high, mostly loads. Nevertheless, design of main frame is dependent on experience, and it will cause reliability reduction and cost increase. This research purpose is to propose and verify a method to achieve higher product quality, lower costs, and far less physical testing. In this study, design parameters used for optimization are each thickness of 4 square pipes and 1 plate in the main frame. The result after optimization showed that the weight of main frame reduced to maximum 6.5% when compared with the initial design in main frame.
Abstract
This study is concerned about the optimal design of the main frame in a moper. Mopper is widely used for cleaning in the fields such as airport, subway, train station, large shopping mall, department store, hospital, government buildings, school, industrial building floor, etc. Especially, main frame in mopper are stressed by high, mostly loads. Nevertheless, design of main frame is dependent on experience, and it will cause reliability reduction and cost increase. This research purpose is to propose and verify a method to achieve higher product quality, lower costs, and far less physical testing. In this study, design parameters used for optimization are each thickness of 4 square pipes and 1 plate in the main frame. The result after optimization showed that the weight of main frame reduced to maximum 6.5% when compared with the initial design in main frame.
참고문헌 (7)
- 이종신, "트위스트 스크린의 지지 프레임에 대한 최적화 설계 파라미터의 결정", 한국기계기술학회지, 15(2), pp.233~239 (2013), 한국기계기술학회
- 이종신, "고효율 바이브레이팅 스크린 베이스의 최적 설계", 한국기계기술학회지, 14(4), pp.71~77 (2012), 한국기계기술학회
- 조재웅, "불규칙 피로 하중을 받는 자동차의 컨트롤 암의 구조 해석", 한국기계기술학회지, 13(3), pp.87~92 (2011), 한국기계기술학회
- 이종신, "2축 직교좌표 로봇에서 2축 직선 운동 가이드가 로봇의 기계적 성능에 미치는 영향", 한국기계기술학회지, 13(1), pp.95~104 (2011), 한국기계기술학회
- 이종신, "2축 직교좌표 로봇의 성능 향상을 위한 액츄에이터 설계에 관한 연구", 한국기계기술학회지, 12(4), pp.1~10 (2010), 한국기계기술학회
- 이종신, "스카라 로봇의 성능 평가에 의한 제 2 암의 최적 설계", 한국기계기술학회지, 11(2), pp.1~8 (2009), 한국기계기술학회
- 이종신, "스카라 로봇 암의 최적화 설계 및 시뮬레이션", 제어.로봇.시스템학회 논문지, 15(6), pp.612~618 (2009), 제어·로봇·시스템학회