최적화해석을 통한 SUV 자동차용 서브-프레임의 설계변수에 미치는 구성부품의 영향성 평가
Evaluation of Influence of Component Parts on Design Variables of SUV Automotive Sub-frame through Optimization Analysis
2
조회
0
다운로드
4
인용
0
참고문헌
키워드
초록
In this study, stiffness evaluation was conducted on the main member, front cross member, and rear cross member, which are three components of sub-frame for SUVs (sports utility vehicles), through mode analysis. As for the design variables used in the analysis, the maximum frequency was examined by varying the width and height of each of the three parts into four types. Of course, the weight at this time is minimized, and the mode is set as a constraint that only bending occurs and no distortion occurs. As a result of the analysis, the member affecting the 1st mode was the rear cross member, and the member having the greatest influence on the 2nd mode was the front cross member. In addition, the member with the greatest influence on the 3rd mode appeared as the rear cross member, indicating that this part had the greatest effect on the bending stiffness.
Abstract
In this study, stiffness evaluation was conducted on the main member, front cross member, and rear cross member, which are three components of sub-frame for SUVs (sports utility vehicles), through mode analysis. As for the design variables used in the analysis, the maximum frequency was examined by varying the width and height of each of the three parts into four types. Of course, the weight at this time is minimized, and the mode is set as a constraint that only bending occurs and no distortion occurs. As a result of the analysis, the member affecting the 1st mode was the rear cross member, and the member having the greatest influence on the 2nd mode was the front cross member. In addition, the member with the greatest influence on the 3rd mode appeared as the rear cross member, indicating that this part had the greatest effect on the bending stiffness.
참고문헌 (6)
- 김기주, "컴퓨터 시뮬레이션(CAE)을 이용한 자동차용 AA6061 리어 서브-프레임 사이드멤버의 하이드로-포밍 공정 개발", 한국자동차공학회 논문집, 18(5), pp.45~49 (2010), 한국자동차공학회
- J. D. Davi, "Aluminum and Aluminum Alloys", pp.678~689 (1993), ASM International
- 김기주, "CAE를 이용한 자동차용 휠캐리어의 경량 설계", 한국기계기술학회지, 18(4), pp.543~549 (2016), 한국기계기술학회[DOI]
- 김기주, "CAE 정적해석을 통한 자동차용 Torque Strut의내구 안전 설계", 한국기계기술학회지, 18(5), pp.694~699 (2016), 한국기계기술학회[DOI]
- 김기주, "강성 확보를 위한 단면 홈 적용 자동차용 서브-프레임 사이드 멤버의 하이드로포밍 공법 설계", 한국기계기술학회지, 20(4), pp.434~438 (2018), 한국기계기술학회[DOI]
- 김기주, "2.9리터 IDI(indirect injection) 엔진용 피스톤의 열전달 해석결과인 열전도로 인한 온도분포를 입력값으로 활용한 열응력 연성 해석", 한국기계기술학회지, 22(3), pp.463~468 (2020), 한국기계기술학회[DOI]