운행 자동차의 진입속도에 따른 동적 제동력 검사 시스템에 미치는 영향
Effect on Dynamic Braking Force Inspection System for Entering Velocity of Vehicles in Service
2
조회
0
다운로드
6
인용
0
참고문헌
키워드
초록
The regular safety inspection of vehicles in service has been tested up to now not by a plate type (dynamic) inspection system but by a roller type (static) inspection system in our country (in Korea). Therefore, the roller type inspection can not reflect the inertia force that there is a load transfer from the rear axle to the front axle during braking. In this study, before introducing the plate type inspection system, the effect on braking force characteristics according to entering velocities of vehicles in service are evaluated statistically. As the results, the reliable entering velocity range is about from 7 km/h to 14 km/h. Also, the regular vehicle safety inspection in domestic country need to adopt the plate type (dynamic) braking force inspection system which can reflect the inertia force.
Abstract
The regular safety inspection of vehicles in service has been tested up to now not by a plate type (dynamic) inspection system but by a roller type (static) inspection system in our country (in Korea). Therefore, the roller type inspection can not reflect the inertia force that there is a load transfer from the rear axle to the front axle during braking. In this study, before introducing the plate type inspection system, the effect on braking force characteristics according to entering velocities of vehicles in service are evaluated statistically. As the results, the reliable entering velocity range is about from 7 km/h to 14 km/h. Also, the regular vehicle safety inspection in domestic country need to adopt the plate type (dynamic) braking force inspection system which can reflect the inertia force.
참고문헌 (16)
- A Study on the Characteristics of Automotive Brake Pedal Force, "H. D. Kim", SAE, 64~75, pp.SAE No. 933712 (1993)
- I. S. Choi, "A Consideration on the Market Situation and The Safety Evaluation Method of the Motor Vehicle equipped with Brake Assist System", KSAE 2010 Conference, KSAE10-B0346, pp.1933~1940 (2010)
- M. S. Pak, "The Development of Braking Ratio Measuring Technique using wheel-torque meter", SAE 1996 Autumn Conference, (96380245), pp.601~607 (1996)
- 김기선, "저속 충돌에 의한 자동차 범퍼의 파손에 대한 유한요소 해석", 한국기계기술학회지, 16(5), pp.1951~1956 (2014), 한국기계기술학회
- 김병삼, "통계적 기법을 이용한 자동차 타이어 도로소음에 관한 연구", 한국기계기술학회지, 15(6), pp.1013~1018 (2013), 한국기계기술학회
- U. S. Yeo, "A Study on Introduction to Dynamic Braking Inspection Equipment of a Vehicle In Service", KSAE 2013 Conference, pp.1266~1272 (2013)
- 오상엽, "운행 휘발유 자동차의 배출가스검사 시스템 비교", 한국자동차공학회 논문집, 22(1), pp.1~7 (2014), 한국자동차공학회[DOI]
- U. S. Yeo, "A Study on Improvement to Underbody Inspection of a Vehicle in Service", KSAE 2013Conference, pp.1254~1259 (2013)
- A Study for Inspection Standard by Advanced Vehicle Inspection System Technology, "B. D. Kang", Inspection Standard Office, Korea Transportation Safety Authority, ~ (2012)
- A Study for High Technology Vehicle Inspection System, "S. Y. Oh", School of Automotive Eng., Kyungpook National University, ~ (2012)
- S. Y. Oh, "Improvement in Emission Inspection System of a Gasoline Vehicle in Service", KSAE Annual Conference, pp.536~542 (2012)
- S. Y. Oh, "Comparison in Braking Force Characteristics for the Static and Dynamic Braking Force Inspection System about Vehicles in Service" (2015), KSAE
- Y. M. Ha, "A Report on 4 Judicial Precedents of the Supreme Court of Korea Concerning Brake System Failure", KSAE 2006 Spring Conference, pp.1018~1023 (2006)
- K. Newton, "The Motor Vehicle", pp.804~829 (1996), SAE
- J. Y. Wong, "Theory of Ground Vehicles", pp.203~271 (2001), John Wile & Sons, INC