180° 곡관을 갖는 원형 혼합배관에서 분기관의 설계인자에 따른 유동특성에 관한 연구
A Study on Flow Characteristics According to Design Parameters of Branch Pipe in Circular Mixing-tee with 180°Curved Pipe
0
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
This study is carried out to analyze the velocity distribution for each location and the uniformity index according to straight distance on exit side by changing the design factors of branch pipe connected to 180° circular mixing-tee using RSM(Reynolds Stress Model) turbulence model. As the results of the flow characteristics according to hydraulic diameter, the velocity profiles in the 90° sectional area are generally similar. In the 180° section, the maximum velocity point shows Y/D=0.7~0.8 after rapid increase of the flow velocity. In the result according to the distance away from inlet, the maximum velocity point in the 90° sectional area is located in outer side of the curved pipe as the distance away from inlet increases. In the 180° sectional area, the maximum velocity point is showed in Y/D=0.7~0.8 after the rapid increase of the flow velocity regardless of the variation of branched distance. In case of inclined angle, the maximum velocity point in the 90° sectional area is located in outer side of the curved pipe as the inclined angle increases. In the 180° sectional area, the maximum velocity point is observed in Y/D=0.8 regardless of the inclined angle. In addition, the uniformity index of flow velocity shows that it is stabilizing after approximately L/D=40 away from the end of the curved pipe regardless of the flow factors in the branch pipe.
Abstract
This study is carried out to analyze the velocity distribution for each location and the uniformity index according to straight distance on exit side by changing the design factors of branch pipe connected to 180° circular mixing-tee using RSM(Reynolds Stress Model) turbulence model. As the results of the flow characteristics according to hydraulic diameter, the velocity profiles in the 90° sectional area are generally similar. In the 180° section, the maximum velocity point shows Y/D=0.7~0.8 after rapid increase of the flow velocity. In the result according to the distance away from inlet, the maximum velocity point in the 90° sectional area is located in outer side of the curved pipe as the distance away from inlet increases. In the 180° sectional area, the maximum velocity point is showed in Y/D=0.7~0.8 after the rapid increase of the flow velocity regardless of the variation of branched distance. In case of inclined angle, the maximum velocity point in the 90° sectional area is located in outer side of the curved pipe as the inclined angle increases. In the 180° sectional area, the maximum velocity point is observed in Y/D=0.8 regardless of the inclined angle. In addition, the uniformity index of flow velocity shows that it is stabilizing after approximately L/D=40 away from the end of the curved pipe regardless of the flow factors in the branch pipe.
참고문헌 (12)
- J. A. C. Humphrey, "Turbulent flow in a square duct with strong curvature", J. Fluid Mech, 103 (1981)
- S. M. Chang, "Turbulent flow in a strongly curved U-bend and downstream tangent of square cross-sections", PCH PhysicoChemical Hydrodynamics, 4(3), pp.243~269 (1983)
- M. Rowe, "Measurement and computations of flow in pipe bends", J. Fluid Mech, 43, pp.771~783 (1970)
- J. Azzola, "Developing turbulent flow in a U-bend of circular cross section : Measurement and Computation", Trans. ASME of J. Fluids Eng, 108, pp.214~221 (1986)
- 고동훈, "U-자형 곡관내의 유동특성에 대한 수치해석적 연구", 한국전산유체공학회지, 14(3), pp.105~114 (2009), 한국전산유체공학회
- 명현국, "원형 단면을 갖는 180° 굽은 곡관내 발달하는 난류유동에 관한 수치해석", 대한기계학회논문집 B, 30(10), pp.966~972 (2006), 대한기계학회
- S. Moravec, "Flow investigation in a model of a three dimensional human artery with Newtonian and Non-Newtonian fluids(Part Ⅰ)", Biorheology, 20(6), pp.745~759 (1983)
- P. Rudolf, "Flow characteristics of curved ducts", Applied and Computational Mechanics, 1, pp.255~264 (2007)
- 이형민, "180° 원형 혼합배관에서 위치별 속도분포 및 출구직관거리의 균일도 특성에 관한 연구", 한국기계기술학회지, 21(2), pp.213~220 (2019), 한국기계기술학회[DOI]
- "ANSYS FLUENT Theory Guide 16.1", ANSYS Inc, ~ (2016)
- G. H. Lee, "Experimental study of turbulent flow in a U-bend of circular cross-section", Transactions of the Korean Society of Mechanical Engineers-B, 22(7), pp.956~965 (1998)
- C. P. Om Ariara Guhan, "Numerical optimization of flow uniformity inside an under body–oval substrate to improve emissions of IC engines", Journal of Computational Design and Engineering, 3, pp.198~214 (2016)