철근콘크리트 전단벽-모멘트골조 형식 건물에 대한 마찰형 감쇠기 설치방식 비교연구
Configurations of the Friction Dampers Installed in a Reinforced Concrete Shear Wall-Moment Frame System
1
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
본 연구에서는 전단벽-모멘트골조 시스템으로서 전단벽이 주로 횡력을 부담하는 철근콘크리트 건물을 대상으로 다양한 설치형식과 마찰력의 총량 및 분포를 갖는 마찰형 감쇠기의 제진보강 효과를 수치해석을 통해 비교?분석하였다. 감쇠기의 설치형식으로서 전단벽에 인접한 대각가새형, 벽체가 없는 골조를 보강하는 대각가새형 및 벽체 단부를 보강하는 수직경계요소형을 고려하였다. 하중기준 강화로 설계용보다 크게 증가한 지진하중에 대해 건물의 재료비선형성을 고려한 비선형시간이력해석을 수행하여 에너지소산, 횡하중 및 부재손상도 측면에서 마찰형 감쇠기의 제진성능을 비교?분석하였다. 기준마찰력의 30% 수준의 총마찰력을 갖는 벽체보강 대각가새형 설치형식이 전반적으로 가장 우수한 제진성능을 보이며, 이 경우에 마찰력 배분방식은 중요하지 않았다. 또한 일부층에 집중설치함으로써 전층설치에 약간 못미치는 제진성능을 얻을 수 있었다.
Abstract
In this study, seismic control performance of friction dampers installed in a reinforced concrete shear wall-moment frame system, of which main lateral force resisting system is a shear wall, is investigated. Three configurations of friction dampers are investigated. One is a diagonal brace type reinforcing the shear wall directly, another is a diagonal brace type reinforcing the moment frame without the shear wall, and the other one is a vertical boundary element type installed at both ends of the shear wall. In addition, various levels of the total friction force and its distribution methods are examined. Time history analysis considering material nonlinearity is conducted for seismic loads increased by the enhanced design code compared to the initial design loads, and energy dissipation, lateral loads and structural member damages are analyzed. As a result, the shear wall-reinforcing diagonal brace type with the total friction force of 30 % of the reference friction force gives the best performance on the whole, and the distribution methods of the friction force do not have remarkable difference in effects. Also, concentrated installation in adjacent four stories shows just a little compromised control performance compared to the entire story installation.
참고문헌 (28)
- 정미영, "하중기준 변 화에 따른노후공동주택의내진성능향상기법에대한고찰", 한 국콘크리트학회 춘계학술발표대회논문집, pp.821~826 (2001)
- 권영웅, "철근콘크리트 전단벽식 건물의 내진성능지수", 한국콘크리트학회 추계학술발표대회논문집, pp.148~151 (2003)
- 최혁준, "내진설계되지 않은 공동주택의 내진성 능지수산정에 관한 연구", 대한건축학회 창립60주년기념 학술 발표대회논문집, 통권 : 25, pp.243~246 (2005)
- Moreschi L.M., "Design of yielding metallic and friction dampers for optimal seismic performance", Earthquake Engineering & Structural Dynamics, 32(8), pp.1291~1311 (2003)
- Levy R., "A simple approach to the seismic design of friction damped mediumrise frames", Engineering Structures, 23(3), pp.250~259 (2001)
- Garcia D.L., "Efficiency of a simple approach to damper allocation in MDOF structures", Journal of Structural Control, (1), pp.19~30 (2002)
- Chang-Geun C., "Development and modeling of a frictional wall damper and its applications in reinforced concrete frame structures", Earthquake Engineering and Structural Dynamics, 33, pp.821~838 (2004)
- Soong, T.T., "Passive Energy Dissipation Systems in Structural Engineering", pp.356~ (1997), John Wiley & Sons
- Experimental and analytical investigation of seismic retrofit of structures with supplemental damping: part II - friction devices, "Li C.", State University of New York at Buffalo, ~, pp.Technical Report NCEER-95-0009 (1995)
- Pall A.S., "Response of friction damped braced frames", Journal of Structural Engineering, 108(9), pp.1313~1323 (1982)
- Mualla, I.H., "Performance of steel frames with a new friction damper device under earthquake excitation", Engineering Structures, 24(3), pp.365~371 (2002)
- Filiatrault A., "Seismic design spectra for frictiondamped structures", Journal of Structural Engineering, 116, pp.1334~1355 (1990)
- Ciampi V., "Design of yielding or friction based dissipative bracing for seismic protection of buildings", Engineering Structures, 17(5), pp.381~391 (1995)
- Inoue, K., "Optimum strength ratio of hysteretic damper", Earthquake Engineering & Structural Dynamics, 27, pp.577~599 (1998)
- Fu, Y., "Design of friction damped structures using lateral force procedure", Earthquake Engineering & Structural Dynamics, 29, pp.989~1010 (2000)
- Lin, Y.Y., "Direct displacement-based design for building with passive energy dissipation systems", Engineering Structures, 25(1), pp.25~37 (2003)
- 이상현, "건축구조물의 층전단력 분포에 기초한 마찰감쇠기의 최적설계", 한국지진공학회논문집, 9(6), pp.21~30 (2005), 한국지진공학회
- 대한건축학회, "건축물하중기준 및 해설", pp.345~ (2000), 대한건축학회
- 대한건축학회, "건축구조설계기준", pp.597~ (2005), 대한건축학회
- ATC, "Seismic Evaluation and Retrofit of Concrete Buildings" (1996), Applied Technology Council
- Vulcano, A., "Analytical models for prediction the lateral response of RC shear wall : Evaluation of their reliability", pp.99~ (1987), Earthquake Engineering Research Center
- Kutay, O., "Nonlinear modeling and analysis of slender reinforced concrete walls", ACI Structural Journal, 101(5), pp.688~698
- Kent, D.C., "Flexural members with confined concrete", J. Struct. Div, 97(7), pp.1969~1990 (1971)
- Scott, M.H., "Plastic Hinge Intergration Methods for Force-Based Beam-Column Elements", pp.244~252 (2006), Journal of Structural Engineering
- Jennings, P.C., "Simulated earthquake motions", pp.52~ (1968), California Institute of Technology
- Wolfe, J., "Propped Shear Walls", Modern steel construction, 41(1), pp.46~53 (2001)
- 대한건축학회, "강구조한계상태설계기준 및 해설", pp.249~ (1998), 대한건축학회
- Salmon, C.G., "Steel Structures", pp.1024~ (1996), Harper Collins