외압을 받는 두꺼운 원통형 내압용기의 붕괴하중 해석
The Analysis of Collapse Load of Thick Pressure Cylinder under External Hydrostatic Pressure
1
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
Number of studies on the buckling of thin cylindrical pressure vessels, such as submarine pressure hull and pipe with a large ratio of diameter/thickness, have been carried out in the naval and ocean engineering. However, research about thick cylinder pressure vessel has not been active except for the specific application in nuclear area. There are not many papers for the estimation of buckling and ultimate load capacity of thick cylinders for the deep sea usage. Thus, it is important to understand the theoretical bases of the buckling and collapse process and the derivation process of such loads for the proper design and structural analysis. The objective of this study is to survey the collapse behavior, to analyse and clarify the derivation procedure and to estimate the ultimate collapse load for thick cylinder by analyzing relevant books and papers. It is found that the yielding begins at the internal surface of the thick cylinder and plasticity develops from the internal surface to the external surface to generate collapse. Also the initial imperfection of cylinder develops flattening and consequently accelerates buckling and finally ultimate collapse. By comparing the collapse loads of aluminum thick cylinder by applying equations herein, it is shown that the equations analyzed are appropriate to obtain collapse load for thick cylinder.
Abstract
Number of studies on the buckling of thin cylindrical pressure vessels, such as submarine pressure hull and pipe with a large ratio of diameter/thickness, have been carried out in the naval and ocean engineering. However, research about thick cylinder pressure vessel has not been active except for the specific application in nuclear area. There are not many papers for the estimation of buckling and ultimate load capacity of thick cylinders for the deep sea usage. Thus, it is important to understand the theoretical bases of the buckling and collapse process and the derivation process of such loads for the proper design and structural analysis. The objective of this study is to survey the collapse behavior, to analyse and clarify the derivation procedure and to estimate the ultimate collapse load for thick cylinder by analyzing relevant books and papers. It is found that the yielding begins at the internal surface of the thick cylinder and plasticity develops from the internal surface to the external surface to generate collapse. Also the initial imperfection of cylinder develops flattening and consequently accelerates buckling and finally ultimate collapse. By comparing the collapse loads of aluminum thick cylinder by applying equations herein, it is shown that the equations analyzed are appropriate to obtain collapse load for thick cylinder.
참고문헌 (22)
- ASME BPVC (Boiler and Pressure Vessel Code), "Section VIII, Division 1", Rules for Construction of Pressure Vessels, ~ (2010)
- Bickell M., "Pressure Vessel Design and Analysis" (1967), Macmillan Education
- 최혁진, "수심 2000m 용 두꺼운 내압용기의 설계, 구조해석과 내압시험", 대한조선학회 논문집, 53(2), pp.144~153 (2016), 대한조선학회
- Corradi, L., "Collapse Behavior of Moderately Thick Tubes Pressurized from Outside. Nuclear Power - Control, Reliability and Human Factors, Chapter 14", pp.257~274 (2011)
- Corradi, L., "A numerical assessment of the load bearing capacity of externally pressurized moderately thick tubes", International Journal of Pressure vessels and Piping, 86, pp.525~532 (2009)
- Harvey, J. F., "Theory and Design of Pressure Vessels" (1991), Van Nostrand Reinhold
- Kardomateas, G. A., "Buckling of thick orthotropic cylindrical shells under external pressure", Journal of Applied Mechanics-Transactions of ASME, 60, pp.195~202 (1993)
- Kardomateas, G. A., "Effect of normal strains in buckling of thick orthotropic shells", Journal of Aerospace Engineering, 13(3), pp.85~91 (2000)
- Kardomateas, G. A., "Buckling of thick orthotropic cylindrical shells under combined external pressure and axial compression", AIAA, 33(10), pp.1946~1953 (1995)
- 김흥열, "소형 잠수함 압력선체의 구조설계", 대한조선학회 논문집, 49(2), pp.116~123 (2012), 대한조선학회[DOI]
- Koiter, W. T., "General theorems of elastic plastic solids mechanics, 1", pp.65~221 (1960)
- Marin J., "Strength of thick-walled cylindrical pressure vessels", Journal of Engineering for Industry, pp.405~415 (1963)
- 노인식, "수압을 받는 원통형 실린더의 초기부정을 고려한 좌굴해석", 대한조선학회 논문집, 54(3), pp.267~273 (2017), 대한조선학회[DOI]
- Papadakis, G., "Buckling of thick cylindrical shells under external pressure", International Journal of Solids and Structures, 45, pp.5308~5321 (2008)
- Ross, C.T.F., "Pressure vessels under external pressure:statics and dynamics" (1990), Elsevier Applied Science
- Sadowski A. J., "Solid or shell finite elements to model thick cylindrical tubes and shells under global bending", International Journal of Mechanical Sciences, 74, pp.143~153 (2013)
- Simonen, F. A., "Collapse of thick-walled cylinders under external pressure", Experimental Mechanics, pp.41~48 (1982)
- Timoshenko, S. P., "Theory of elastic stability" (1961), McGraw-Hill Book Company
- Voyiadjis, G. Z., "Refined theory for flexural motions of isotropic elastic plates", Journal of Sound and Vibration, 76(1), pp.57~64 (1981)
- Voyiadjis, G. Z., "A refined two-dimensional theory for thick cylindrical shells", International Journal of Solids and Structures, 27(3), pp.261~282 (1991)
- Voyiadjis, G. Z., "A refined theory for thick spherical shells", International Journal of Solids and Structures, 41, pp.3747~3769 (2004)
- YEON-SIK YOO, "COLLAPSE PRESSURE ESTIMATES AND THE APPLICATION OF A PARTIAL SAFETY FACTOR TO CYLINDERS SUBJECTED TO EXTERNAL PRESSURE", Nuclear Engineering and Technology, 42(4), pp.450~459 (2010), 한국원자력학회