임플랜트 지대주 나사의 텅스텐 카바이드/탄소 코팅이 나사풀림에 미치는 영향
Influence of tungsten carbide/carbon coating of implant-abutment screw on screw loosening
1
조회
0
다운로드
3
인용
0
참고문헌
키워드
초록
임플랜트 보철물에서 각 구성 요소를 연결하는 나사 풀림 현상이 흔히 발생하고 있다. 나사 풀림을 최소화하기 위해서 연결 구성 부품 사 이의 압축력을 최대로 하는 것이 중요한데, 나사 신장의 허용 한계 내에서 조임회전력을 증가시켜 나사 내부의 인장력 즉 전하중을 극대화하 기 위해서는 마찰 계수를 감소시켜 초기 조임회전력의 손실을 최소화해야 한다. 건조 윤활제를 나사 표면에 코팅한 나사들이 전하중을 증가 시키고 나사 풀림을 감소시키나 나사의 반복체결에 따른 코팅표면의 마모가 문제점으로 지적되고 있다. 최근 내마모성이 우수하며 동시에 나 사의 마찰 저항을 최소화할 수 있는 텅스텐 카바이드/탄소 코팅을 이용한 나사가 임상에 사용되고 있으나 실제적으로 연결부 안정성에 미치 는 영향에 관한 연구는 미미한 편이다. 이에 본 연구에서는 external butt joint 형태를 가지는 US II 시스템과 one stage용 8도의 internal cone 연결형태의 SS II 시스템 및 11도의 internal cone 연결형태의 GS II 시스템에서 티타늄 합금 나사의 텅스텐 카바이드/탄소 코팅이 지대주 나사 풀림에 미치는 영향을 알아보기 위하여 100만 회 반복 하중 전후의 풀림회전력 및 상실률을 비교한 결과 다음과 같은 결론을 얻었다. 1. 초기 풀림회전력은 티타늄 합금나사보다 텅스텐 카바이드/탄소 코팅 나사를 사용한 경우 작게 나타났으며 (P<.01), 동일 나사를 사용 한 경우에는 임플랜트 시스템 간에 차이가 없었다 (P>.05). 2. 반복하중에 따른 풀림회전력의 상실률은 두 나사 모두에서 external butt joint 형태의 US II 시스템이 internal cone 연결형태의 SS II 와 GS II 시스템 보다 크게 나타났으나, SS II 와 GS II 시스템 사이에는 차이를 보이지 않았다 (P<.01). 3. 텅스텐 카바이드/탄소 코팅 나사를 사용한 경우 티타늄 합금 나사에 비해 모든 시스템에서 반복하중 후 풀림회전력 상실률이 작게 나타 났으며 (P<.01), 코팅 나사 사용으로 인한 상실률의 감소차는 임플랜트 시스템 간에 차이를 보이지 않았다
Abstract
Statement of problem: Dental implant procedure has been recognized as a very effective treatment to rehabilitate fully or partially edentulous patients. However, mechanical failures such as screw loosening, screw fracture have been still reported frequently. Purpose: The purpose of this study was to evaluate the influence of tungsten carbide/carbon coating, which has superior hardness and frictional wear resistance, on implant-abutment screw loosening of three different joint connections after one million cyclic loading. Material and methods: The values of detorque before and after loading were measured in three different joint connections (Osstem Implant, Korea), one external butt joint, US II implant system and two internal cones, SS II and GS II system. The values of detorque before loading was analyzed by one-way ANOVA ,and two-way ANOVA and Scheffe’test were performed for the value of detorque after loading. Results: 1. The values of initial detorque of tungsten carbide/carbon coated Ti alloy screw were smaller those of Ti alloy screw (P<.01), and there were no differences among implant systems in each screw (P>.05). 2. In comparison of loss rate of detorque value after cyclic loading, US II system was greater than SS II and GS II system but there was no difference between SS II and GS II system (P<.01). 3. Loss rates of detorque value after cyclic loading decreased consistently at tungsten carbide/carbon coated Ti alloy screw comparing with Ti alloy screw in all implant systems (P<.01), and there were no differences among three systems in reduction of loss rates by using tungsten carbide/carbon coated Ti alloy screw (P>.05). Conclusion: Tungsten carbide/carbon coating to increase preload with reduction of friction resistance was a effective way to decrease screw loosening by functional loading.
참고문헌 (39)
- "Osseointegration and its experimental background", J Prosthet Dent, 50, pp.399~410 (1983)
- Jemt T, "Multicenter study of overdentures supported by Branemark", Int J Oral Maxillofac Implants, 7, pp.513~522 (1992)
- Jemt T, "Osseointegrated implants for single tooth replacement: a 1-year report from a multicenter prospective study", Int J Oral Maxillofac Implants, 6, pp.29~36 (1991)
- Anderson B, "Singletooth restorations supported by osseointegrated implants: results and experiences from a prospective study after 2 to 3 years", Int J Oral Maxillofac Implants, 10, pp.702~711 (1995)
- Binon PP, "The role of screws in implant systems", Int J Oral Maxillofac Implants, 9, pp.48~63 (1994)
- McGlumphy EA, "Implant Screw Mechanics", Dent Clinics North Am, 42, pp.71~89 (1998)
- Rangert B, "Forces and Moments on Branemark Implants", Int J Oral Maxillofac Implants, 4, pp.241~247 (1989)
- Burguete RL, "Tightening characteristics for screwed joints in the osseointegrated dental implants", J Prosthet Dent, 71, pp.592~595 (1994)
- Wiskott HW, "Resistance of ITI implant connectors to multivectorial fatigue load application", Int J Prosthodont, 17, pp.672~679 (2004)
- Motosch N, "Development of design charts for bolts preloaded up to the plastic range", J Eng Ind, 98, pp.849~851 (1976)
- "J Dent Res", 1998, 837~
- Jorneus L, "Loads and designs of screw joints for single crowns supported by osseointegrated implants", Int J Oral Maxillofac Implants, 7, pp.353~359 (1992)
- Martin WC, "Implant abutment screw rotations and preloads for four different screw materials and surfaces", J Prosthet Dent, 86, pp.24~32 (2001)
- Binon PP, "Implants and components", Int J Oral Maxillofac Implants, 15, pp.633~645 (2000)
- Liu Y, "Nanoscale multilayer WC", C coatings developed for nanopositioning. part II: Friction and wear, 2005, pp.488, 140~148
- 최진욱, "임플랜트 지대주 나사의 텅스텐 카바이드", 탄소 코팅이 전하중에 미치는 영향에 관한 연구, 2006, pp.44(2), 229~242[DOI]
- Shin HM, Jeong CM, Jeon YC, Jeong HC, Eom TG, "Influence of tightening torque on implant-abutment screw joint stability", 석사, pp.2007
- Siamos G, "The relationship between implant preload and screw loosening on implantsupported restorations", J Oral Implantol, 28, pp.67~73 (2002)
- ISO, "FDIS 14801 Dentistry", Fatigue test for endosseous dental implants, International Organization for Standardization, 2003
- Mericske-Stern R, "In vivo measurements of some functional aspects with mandibular fixed prostheses supported by implants", Clin Oral Implants Res, 7, pp.153~161 (1996)
- Richter EJ, "In vivo vertical forces on implants", Int J Oral Maxillofac Implants, 10, pp.99~108 (1995)
- Mohl ND, "A Textbook of Occlusion", pp.143~152 (1988), Quintessence
- Wiskott HW, "Stress fatigue: basic principles and prosthodontic implications", Int J Prosthodont, 8, pp.105~116 (1995)
- Pang W, "Laser surface coating of Mo-C metal matrix composite on Ti6Al4V alloy", Mat Sci Eng A, 390, pp.144~153 (2005)
- Saenger R, "Electrochemical characterization of plasma sprayed WC-CO coatings by imped-ance techniques", Surf Coat Technol, 194, pp.335~343 (2005)
- Kirkwood WF, ". Handbook of Mechanics, Materials, and Structures", pp.320~328 (1985), Wiley
- Leempoel PJB, "Survival studies of restorations: Criteria, methods and analyses", J Oral Rehabil, 16, pp.387~394 (1989)
- Merz BR, "Mechanics of the implant-abutment connection: an 8-degree taper compared to a butt joint connection", Int J Oral Maxillofac Implants, 15, pp.519~526 (2000)
- Cibirka RM, "Exanination of the implant-abutment interface after fatigue testing", J Prosthet Dent, 85, pp.268~275 (2001)
- Binon PP, "Evaluation of machining accuracy and consistency of selected implants, standard abutments, and laboratory analogs", Int J Prosthodont, 8, pp.162~178 (1995)
- Schwarz MS, "Mechanical complications of dental implants", Clin Oral Impl Res, 11, pp.156~158 (2000)
- Griffith HT, "Suggested tightening torques for structural bolts", Fastener Technology (1987)
- Sutter F, "The new restorative concept of the ITI dental implant system: design and engineering", Int J Periodont Rest Dent, 13, pp.409~431 (1993)
- Balfour A, "Comparative study of antirotational single tooth abutments", J Prosthet Dent, 73, pp.36~43 (1995)
- Gratton DG, "Micromotion and dynamic fatigue properties of the dental implant-abutment interface", J Prosthet Dent, 85, pp.47~52 (2001)
- Weiss EI, "Effect of repeated closures on opening torque values in seven abutment-implant systems", J Prosthet Dent, 84, pp.194~199 (2000)
- Alkan I, "Influence of occlusal forces on stress distribution in preloaded dental implant screws", J Prosthet Dent, 91, pp.319~325 (2004)
- Mollersten L, "Comparison of strength and failure mode of seven implant systems: An in vitro test", J Prosthet Dent, 78, pp.582~591 (1997)
- Pattern EA, "Theoretical analysis of the fatigue life of fixture screws in osseointegrated dental implants", Int J Oral Maxillofac Implants, 7, pp.26~34 (1992)