납과 텅스텐 기반 차폐체의 성능 비교 평가
Evaluation of the Shield Performance of Lead and Tungsten Based Radiation Shields
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
This study was intended to evaluate the shielding rate of radiation shields manufactured using 3D printers that have recently been used in various fields by comparing them with existing shields made of lead, and to find out their applicability through experiments. A 3D printer shield made of tungsten filament 1 mm, 2 mm, 4 mm shield, RNS-TX (nanotungsten) 1.1 mm, lead 0.2 mmPb, and 1mmPb were exposed to 99mTc, 18F, and 201TI for 15, 30, 45 minutes, and 60 minutes after measuring cumulative dose three times. Based on this, the shielding rate of each shield was calculated based on the dose in the absence of the shield. In addition, 99mTc, 18F, and 201TI were located 100 cm away from the phantom in which the OSLD nano Dot device was inserted, and if there was no shield for 60 minutes, the dose of thyroid was measured using 1.0 mm of lead shield, 1.1 mm of RNS-TX shield, and 2 mm of tungsten shield made by 3D printer. The use of shields during radiation shielding emitted from open radiation sources all resulted in a reduction in dose. The radiation dose emitted from the radionuclides under the experiment was all reduced when the shield was used. This study has been confirmed that tungsten is a material that can replace lead due to its excellent performance and efficiency as shield, and that it even shows the possibility of manufacturing a customized shield using 3D printer.
Abstract
This study was intended to evaluate the shielding rate of radiation shields manufactured using 3D printers that have recently been used in various fields by comparing them with existing shields made of lead, and to find out their applicability through experiments. A 3D printer shield made of tungsten filament 1 mm, 2 mm, 4 mm shield, RNS-TX (nanotungsten) 1.1 mm, lead 0.2 mmPb, and 1mmPb were exposed to 99mTc, 18F, and 201TI for 15, 30, 45 minutes, and 60 minutes after measuring cumulative dose three times. Based on this, the shielding rate of each shield was calculated based on the dose in the absence of the shield. In addition, 99mTc, 18F, and 201TI were located 100 cm away from the phantom in which the OSLD nano Dot device was inserted, and if there was no shield for 60 minutes, the dose of thyroid was measured using 1.0 mm of lead shield, 1.1 mm of RNS-TX shield, and 2 mm of tungsten shield made by 3D printer. The use of shields during radiation shielding emitted from open radiation sources all resulted in a reduction in dose. The radiation dose emitted from the radionuclides under the experiment was all reduced when the shield was used. This study has been confirmed that tungsten is a material that can replace lead due to its excellent performance and efficiency as shield, and that it even shows the possibility of manufacturing a customized shield using 3D printer.
참고문헌 (14)
- 한상현, "텅스텐 차폐체의 감마선 투과선량 측정", 한국산학기술학회논문지, 19(9), pp.124~129 (2018), 한국산학기술학회[DOI]
- Han SH, "Performance evaluation of gamma-ray shielding to produce a nuclear medicine exclusive apron", pp.2017
- Finnerty M, "Protective aprons in imaging departments : Manufacturer stated lead equivalence values require validation", European Radiology, 15(7), pp.1477~1484 (2005)[DOI]
- 이왕희, "핵의학과 내 작업 환경에서 공기층 납치마의 피폭선량 감소 효과 평가", 한국콘텐츠학회 논문지, 14(12), pp.845~853 (2014), 한국콘텐츠학회[DOI]
- Mori H, "Evaluation of the effectiveness of X-ray protective aprons in experimental and practical fields", Radiological Physics and Technology, 7, pp.158~166 (2014)[DOI]
- 최태진, "의료영상용 방사선방호를 위한 무납차폐체 개발", 의학물리, 21(2), pp.232~237 (2010), 한국의학물리학회
- "The effect of a radio-protective apron and working posture on EMG activities of muscles of neck extender, trapezius and lumbar erector spine" (2004)[URL]
- 오왕균, "의료 영상을 이용한 인체 골 모형 제작의 3차원 프린팅 시스템 개발", 방사선기술과학, 40(3), pp.433~441 (2017), 대한방사선과학회[DOI]
- 박훈희, "PET", CT 검사에서 비스무스(bismuth) 차폐체의 적용에 따른 유용성 평가, 2014, pp.37(1), 49~56[DOI]
- 이홍연, "3D 프린팅 기술을 이용한 원료에 대한 방사선 차폐능 평가: FDM 방식의 3D 프린팅 기술을 중심으로", 한국방사선학회논문지, 12(7), pp.909~917 (2018), 한국방사선학회[DOI]
- Dong KR, "A study of individual dose for radiological technologists working with easiest", Journal of Korean Society for Indoor Environment, 6(1), pp.38~47 (2009)[DOI]
- Raissaki M, "Eye-lens bismuth shielding in paediatric head CT : Artifact evaluation and reduction", Pediatric Radiology, 40(11), pp.1748~1754 (2010)[DOI]
- Wu Y, "Mechanical properties and ga㎜a-ray shielding performance of 3D-printed poly-ether-ether-ketone", tungsten composites, 2020, pp.13(20), 4475~
- 윤준, "일반촬영분야에서의 3D 프린터로 제작한 텅스텐 혼합 필라멘트 차폐체의 성능평가", 방사선기술과학, 44(6), pp.615~621 (2021), 대한방사선과학회