반응물 분사조건에 따른 무화염 연소특성 연구
Combustion Characteristics of Flameless Combustion by Reactants Injection Conditions
1
조회
0
다운로드
6
인용
0
참고문헌
키워드
초록
The flameless combustion has been considered as one of the promising combustion technology for high thermal efficiency, reducing NOx and CO emissions. In this paper, the effect of air and fuel injection condition on formation of flameless combustion was analyzed using three dimensional numerical simulation. The results show that the high temperature region and the average temperature was decreased due to increase of recirculation ratio when air velocity is increased. The average temperature was also affected by entrainment length. Generally mixing effect was enhanced at low entrainment length and dilution was dominated at high entrainment length. This entrainment length was greatly affected by air and fuel injection velocity and distance between air and fuel. It is also found that the recirculation ratio and dilution effect were generally increased by entrainment length and the recirculation ratio, mixing and dilution effect are the significant factor for design of flameless combustion system.
Abstract
The flameless combustion has been considered as one of the promising combustion technology for high thermal efficiency, reducing NOx and CO emissions. In this paper, the effect of air and fuel injection condition on formation of flameless combustion was analyzed using three dimensional numerical simulation. The results show that the high temperature region and the average temperature was decreased due to increase of recirculation ratio when air velocity is increased. The average temperature was also affected by entrainment length. Generally mixing effect was enhanced at low entrainment length and dilution was dominated at high entrainment length. This entrainment length was greatly affected by air and fuel injection velocity and distance between air and fuel. It is also found that the recirculation ratio and dilution effect were generally increased by entrainment length and the recirculation ratio, mixing and dilution effect are the significant factor for design of flameless combustion system.
참고문헌 (14)
- C. S. Lee, "Activities on IEA", ECERC Delegation of Korea, 2012, pp.17(4), 1~4
- J. Li, "Volumetric combustion of biomass for CO2 and NOx reduction in coal-fired boilers", Fuel, 102, pp.624~633 (2012)
- B. O. Yang, "Experimental Study on High Temperature Air Regenerative Combustion System", 19th KOSCO Symposium, pp.189~200 (1999)
- E. S. Cho, "Behavior of a 300 kWth regenerative multi-burner flameless oxidation furnace", Applied Energy, 88, pp.4592~4959 (2001)
- J. A. Wünning, "FLAMELESS OXIDATION TO REDUCE THERMAL NO-FORMATION", Progress in Energy and Combustion Science, 23, pp.81~94 (1997)
- A. S. Verissimo, "Importance of the inlet air velocity on the establishment of flameless combustion in a laboratory combustor", Experimental Thermal and fluid Sience, 44, pp.75~81 (2013)
- K. Arghode, "Effect of flow field for colorless distributed combustion(CDC) for gas turbine combustion", Applied Energy, 87, pp.1631~1640 (2010)
- K. Arghode, "Investigation of forward flow distributed combustion for gas turbine application", Applied Energy, 88, pp.29~40 (2011)
- K. Arghode, "Investigation of reverse flow distributed combustion for gas turbine application", Applied Energy, 88, pp.1096~1104 (2011)
- G. G. Szegö, "Operational characteristics of a parallel jet MILD combustion burner system", Combustion and Flame, 156, pp.429~438 (2009)
- J. Mi, "Impact of injection conditions on flame characteristics from a parallel multi-jet burner", Energy, 36, pp.6583~6595 (2011)
- E. Khalil, "Swirling distributed com bustion for clean energy conversion in gas turbine applications", Applied Energy, 88, pp.3685~3693 (2011)
- E. W. Grandmaison, "The Strong-Jet", Weak-Jet Problem and Aerodynamic Modeling of the CGRI Burner, 1998, pp.114, 381~396
- B. E. Launder, "The numerical computation of turbulent flows", Computer Methods in Applied Mechanics and Engineering, 3, pp.269~289 (1974)