Cr-Si-Al-N 코팅의 상형성 및 표면 물성에 미치는 Si 함량의 영향
Effect of Si Content on the Phase Formation Behavior and Surface Properties of the Cr-Si-Al-N Coatings
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Cr-Si-Al-N coating with different Si content were deposited by hybrid physical vapor deposition (PVD) method consisting of unbalanced magnetron (UBM) sputtering and arc ion plating (AIP). The deposition temperature was 300oC, and the gas ratio of Ar/N2 were 9:1. The CrSi alloy and aluminum targets used for arc ion plating and sputtering process, respectively. Si content of the CrSi alloy targets were varied with 1 at%, 5 at%, and 10 at%. The phase analysis, composition and microstructural analysis performed using xray diffraction (XRD) and field emission scanning electron microscopy (FESEM) including energy dispersive spectroscopy (EDS), respectively. All of the coatings grown with textured CrN phase (200) plane. The thickness of the Cr-Si-Al-N films were measured about 2 μm. The friction coefficient and removal rate of films were measured by a ball-on-disk test under 20N load. The friction coefficient of all samples were 0.6 ~ 0.8. Among all of the samples, the removal rate of CrSiAlN (10 at% Si) film shows the lowest values, 4.827 × 10−12mm3/ Nm. As increasing of Si contents of the CrSiAlN coatings, the hardness and elastic modulus of CrSiAlN coatings were increased. The morphology and composition of wear track of the films was examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy, respectively. The surface energy of the films were obtained by measuring of contact angle of water drop. Among all of the samples, the CrSiAlN (10 at% Si) films shows the highest value of the surface energy, 41 N/m.
Abstract
Cr-Si-Al-N coating with different Si content were deposited by hybrid physical vapor deposition (PVD) method consisting of unbalanced magnetron (UBM) sputtering and arc ion plating (AIP). The deposition temperature was 300oC, and the gas ratio of Ar/N2 were 9:1. The CrSi alloy and aluminum targets used for arc ion plating and sputtering process, respectively. Si content of the CrSi alloy targets were varied with 1 at%, 5 at%, and 10 at%. The phase analysis, composition and microstructural analysis performed using xray diffraction (XRD) and field emission scanning electron microscopy (FESEM) including energy dispersive spectroscopy (EDS), respectively. All of the coatings grown with textured CrN phase (200) plane. The thickness of the Cr-Si-Al-N films were measured about 2 μm. The friction coefficient and removal rate of films were measured by a ball-on-disk test under 20N load. The friction coefficient of all samples were 0.6 ~ 0.8. Among all of the samples, the removal rate of CrSiAlN (10 at% Si) film shows the lowest values, 4.827 × 10−12mm3/ Nm. As increasing of Si contents of the CrSiAlN coatings, the hardness and elastic modulus of CrSiAlN coatings were increased. The morphology and composition of wear track of the films was examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy, respectively. The surface energy of the films were obtained by measuring of contact angle of water drop. Among all of the samples, the CrSiAlN (10 at% Si) films shows the highest value of the surface energy, 41 N/m.
참고문헌 (20)
- H. C. Barshilia, "Structure, hardness and thermal stability of nanolayered TiN", CrN multilayer coatings, 2003, pp.72, 241~248
- P. Mayrhofer, "and mechanical", thermal properties of Cr–N coatings deposited by reactive unbalanced magnetron sputtering, 2001, pp.142, 78~84
- n multilayer system, "J. Mater. Sci. Emg. B", 2010, 56~61
- J. B. Choi, "Effects of Si content and free Si on oxidation behavior of Ti–Si–N coating layers", Thin Solid Films, 447, pp.365~370 (2004)
- Y. Chim, "Oxidation resistance of TiN, CrN, TiAlN and CrAlN coatings deposited by lateral rotating cathode arc", Thin Solid Films, 517, pp.4845~4849 (2009)
- G Abadias, "Stress, phase stability and oxidation resistance of ternary Ti-Me-N (Me= Zr, Ta) hard coatings", Thin Solid Films, 538, pp.56~70 (2013)
- I. -W. Park, "Microstructures, mechanical properties, and tribological behaviors of Cr–Al–N, Cr–Si–N, and Cr–Al–Si–N coatings by a hybrid coating system", Surf. coat. Technol, 201, pp.5223~5227 (2007)
- D. Mercs, "Mechanical and tribological properties of Cr–N and Cr–SI–N coatings reactively sputter deposited", Surf. coat. Technol, 200, pp.403~407 (2005)
- M. Brizuela, "Magnetron sputtering of Cr (Al) N coatings: mechanical and tribological study", Surf. coat. Technol, 200, pp.192~197 (2005)
- H. C. Barshilia, "A comparative study of reactive direct current magnetron sputtered CrAlN and CrN coatings", Surf. coat. Technol, 201, pp.2193~2201 (2006)
- E. Forniés, "Growth of CrN x films by DC reactive magnetron sputtering at constant N 2", Ar gas flow, 2006, pp.200, 6047~6053
- D. Depla, "Target surface condition during reactive glow discharge sputtering of copper", Plasma Sources. Sci. Technol, 11, pp.91~ (2002)
- S. Berg, "Fundamental understanding and modeling of reactive sputtering processes", Thin solid films, 476, pp.215~230 (2005)
- 양영환, "중간층 조건에 따른 Cr-Mo-N 막의 상형성 및 마찰마모 거동 연구", 한국표면공학회지, 44(6), pp.269~276 (2011), 한국표면공학회
- Y. S. Hong, "Effects of Cr interlayer on mechanical and tribological properties of Cr-Al-Si-N nanocomposite coating", Trans. Nonferrous Met. Soc. China, 21, pp.s62~s67 (2011)
- J.-W. Lee, "A study on the microstructures and mechanical properties of pulsed DC reactive magnetron sputtered Cr–Si–N nanocomposite coatings", Surf. coat. Technol, 202, pp.831~836 (2007)
- P. M. Martin, "Handbook of deposition technologies for films and coatings: science, applications and technology", William Andrew, pp.257~ (2009)
- H.-W. Chen, "Oxidation behavior of Si-doped nanocomposite CrAlSiN coatings", Surface and Coatings Technology, 205, pp.1189~1194 (2010)
- K. Yamamoto, "Structural analysis of (Cr1-xSix)N coatings and tribological property in water environment", Surf. Coat. Technol, 193, pp.167~172 (2003)
- A. ozturk, "Comparative tribological behaviors of TiN-, CrN- and MoN-Cu nanocomposite coatings", Tribology International, 41, pp.49~59 (2008)