란타넘 산화물의 분산을 통해 향상된 파괴인성을 갖는 몰리브데넘 합금의 제조
Fabrication of Molybdenum Alloys with Improved Fracture Toughness through the Dispersion of Lanthanum Oxide
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
In this study, lanthanum oxide (La2O3) dispersed molybdenum (Mo–La2O3) alloys are fabricated using lanthanum nitrate solution and nanosized Mo particles produced by hydrogen reduction of molybdenum oxide. The effect of La2O3 dispersion in a Mo matrix on the fracture toughness at room temperature is demonstrated through the formation behavior of La2O3 from the precursor and three-point bending test using a single-edge notched bend specimen. The relative density of the Mo–0.3La2O3 specimen sintered by pressureless sintering is approximately 99%, and La2O3 with a size of hundreds of nanometers is uniformly distributed in the Mo matrix. It is also confirmed that the fracture toughness is 19.46 MPa·m1/2, an improvement of approximately 40% over the fracture toughness of 13.50 MPa·m1/2 on a pure-Mo specimen without La2O3, and this difference in the fracture toughness occurs because of the changes in fracture mode of the Mo matrix caused by the dispersion of La2O3.
Abstract
In this study, lanthanum oxide (La2O3) dispersed molybdenum (Mo–La2O3) alloys are fabricated using lanthanum nitrate solution and nanosized Mo particles produced by hydrogen reduction of molybdenum oxide. The effect of La2O3 dispersion in a Mo matrix on the fracture toughness at room temperature is demonstrated through the formation behavior of La2O3 from the precursor and three-point bending test using a single-edge notched bend specimen. The relative density of the Mo–0.3La2O3 specimen sintered by pressureless sintering is approximately 99%, and La2O3 with a size of hundreds of nanometers is uniformly distributed in the Mo matrix. It is also confirmed that the fracture toughness is 19.46 MPa·m1/2, an improvement of approximately 40% over the fracture toughness of 13.50 MPa·m1/2 on a pure-Mo specimen without La2O3, and this difference in the fracture toughness occurs because of the changes in fracture mode of the Mo matrix caused by the dispersion of La2O3.
참고문헌 (17)
- J. H. Perepezko, , Science, 326, pp.1068~ (2009)
- D. M. Dimiduk, , MRS Bull, 28, pp.639~ (2003)
- M. S. El-Genk, , J. Nucl. Mater, 340, pp.93~ (2005)
- D. Sturm, , Mater. Sci. Eng., A, 463, pp.107~ (2007)
- J. Wadsworth, , Int. Mater. Rev, 33, pp.131~ (1988)
- B. V. Cockeram, , Metall. Mater. Trans. A, 40, pp.2843~ (2009)
- D. R. Trinkle, , Science, 310, pp.1665~ (2005)
- N. I. Medvedeva, , Phys. Rev. B, 76, pp.212104~ (2007)
- M. K. Miller, , Scr. Mater, 46, pp.299~ (2002)
- A. J. Mueller, , Int. J. Refract. Met. Hard Mater, 18, pp.205~ (2000)
- G. J. Zhang, , Adv. Eng. Mater, 6, pp.943~ (2004)
- B. V. Cockeram, , Mater. Sci. Eng. A, 418, pp.120~ (2006)
- G. Liu, , Nat. Mater, 12, pp.344~ (2013)
- 안치형, "초고압 성형을 통한 Mo 나노 분말의 치밀화", 한국재료학회지, 28(3), pp.166~173 (2018), 한국재료학회
- A. -E. Gobichon, , Solid State Ionics, 93, pp.51~ (1996)
- D. F. Stewart, , J. Phys. Chem, 63, pp.1330~ (1959)
- K. T. Faber, , Acta Metall, 31, pp.565~ (1983)