레이저 직접 용착공정으로 형성된 스테인레스/인코넬 합금 계면의 미세조직 분석
Investigation on Interfacial Microstructures of Stainless Steel/Inconel Bonded by Directed Energy Deposition of alloy Powders
2
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
The directed energy deposition (DED) process of metal 3D printing technologies has been treated as an effective method for welding, repairing, and even 3-dimensional building of machinery parts. In this study, stainless steel 316L (STS316L) and Inconel 625 (IN625) alloy powders are additively manufactured using the DED process, and the microstructure of the fabricated STS316L/IN625 sample is investigated. In particular, there are no secondary phases in the interface between STS316L and the IN625 alloy. The EDS and Vickers hardness results clearly show compositionally and mechanically transient layers a few tens of micrometers in thickness. Interestingly, several cracks are only observed in the STS 316L rather than in the IN625 alloy near the interface. In addition, small-sized voids 200– 400 nm in diameter that look like trapped pores are present in both materials. The cracks present near the interface are formed by tensile stress in STS316L caused by the difference in the CTE (coefficient of thermal expansion) between the two materials during the DED process. These results can provide fundamental information for the fabrication of machinery parts that require joining of two materials, such as valves.
Abstract
The directed energy deposition (DED) process of metal 3D printing technologies has been treated as an effective method for welding, repairing, and even 3-dimensional building of machinery parts. In this study, stainless steel 316L (STS316L) and Inconel 625 (IN625) alloy powders are additively manufactured using the DED process, and the microstructure of the fabricated STS316L/IN625 sample is investigated. In particular, there are no secondary phases in the interface between STS316L and the IN625 alloy. The EDS and Vickers hardness results clearly show compositionally and mechanically transient layers a few tens of micrometers in thickness. Interestingly, several cracks are only observed in the STS 316L rather than in the IN625 alloy near the interface. In addition, small-sized voids 200– 400 nm in diameter that look like trapped pores are present in both materials. The cracks present near the interface are formed by tensile stress in STS316L caused by the difference in the CTE (coefficient of thermal expansion) between the two materials during the DED process. These results can provide fundamental information for the fabrication of machinery parts that require joining of two materials, such as valves.
참고문헌 (14)
- 신기훈, "선택적 레이저 용융공정을 이용한 316L 스테인리스강 분말 3차원 조형체의 미세조직 및 경도 연구", 한국분말재료학회지, 24(3), pp.210~215 (2017), 한국분말재료학회[DOI]
- A. Ambrosi, , Chem. Soc. Rev, 45, pp.2740~ (2016)
- 이기승, "선택적 레이저 용융공정으로 제조된 Al-Si-Mg 합금의 열처리에 따른 미세조직 및 특성평가", 한국분말재료학회지, 26(2), pp.138~145 (2019), 한국분말재료학회[DOI]
- 엄영성, "AlSi10Mg 합금분말 크기가 선택적 레이저 용융된 3차원 조형체 특성에 미치는 영향", 한국분말재료학회지, 27(2), pp.103~110 (2020), 한국분말재료학회[DOI]
- 황준호, "공정 파라미터에 따른 금속분말(SUS316L, IN718) 레이저 적층 표면 및 단면 특성 분석", 대한용접접합학회지, 35(3), pp.28~34 (2017), 대한용접접합학회[DOI]
- I. Gibson, "Additive Manufacturing Technologies", pp.245~ (2015), Springer New York
- A. Saboori, , Appl. Sci, 7, pp.883~ (2017)
- Jun Seok Park, "Effect of Heat Treatment on the Characteristics of Tool Steel Deposited by the Directed Energy Deposition Process", Metals and Materials International, 22(1), pp.143~147 (2016), 대한금속·재료학회[DOI]
- B. E. Carroll, , Acta Mater, 108, pp.46~ (2016)
- T. Abe, , Precis. Eng, 45, pp.387~ (2016)
- G. H. Aydoğdu, , Corros. Sci, 48, pp.3565~ (2006)
- H. Y. Al-Fadhli, , Surf. Coat. Technol, 200, pp.20~ (2006)
- M. Yakout, , Addit. Manuf, 24, pp.40~ (2018)