DED 공정으로 제조된 경사조성재료 (STS 316L과 저합금강)의 미세조직 및 기계적특성 평가
Evaluation of Microstructures and Mechanical Properties in Functionally Graded Materials (STS 316L and Low Alloy Steel) Produced by DED Processes
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
In this study, additive manufacturing of a functionally graded material (FGM) as an alternative to joining dissimilar metals is investigated using directed energy deposition (DED). FGM consists of five different layers, which are mixtures of austenitic stainless steel (type 316 L) and low-alloy steel (LAS, ferritic steel) at ratios of 100:0 (A layer), 75:25 (B layer), 50:50 (C layer), 25:75 (D layer), and 0:100 (E layer), respectively, in each deposition layer. The FGM samples are successfully fabricated without cracks or delamination using the DED method, and specimens are characterized using optical and scanning electron microscopy to monitor their microstructures. In layers C and D of the sample, the tensile strength is determined to be very high owing to the formation of ferrite and martensite structures. However, the elongation is high in layers A and B, which contain a large fraction of austenite.
Abstract
In this study, additive manufacturing of a functionally graded material (FGM) as an alternative to joining dissimilar metals is investigated using directed energy deposition (DED). FGM consists of five different layers, which are mixtures of austenitic stainless steel (type 316 L) and low-alloy steel (LAS, ferritic steel) at ratios of 100:0 (A layer), 75:25 (B layer), 50:50 (C layer), 25:75 (D layer), and 0:100 (E layer), respectively, in each deposition layer. The FGM samples are successfully fabricated without cracks or delamination using the DED method, and specimens are characterized using optical and scanning electron microscopy to monitor their microstructures. In layers C and D of the sample, the tensile strength is determined to be very high owing to the formation of ferrite and martensite structures. However, the elongation is high in layers A and B, which contain a large fraction of austenite.
참고문헌 (20)
- A. Bandyopadhyay, , Mater. Sci. Eng., R, 129, pp.1~ (2018)
- J. O. Milewski, "Additive Manufacturing of Metals" (2017), Springer International Publishing
- 오욱진, "레이저로 적층 제조된 STS316L에 대한 직접에너지적층 응용 보수 시 공정 중 후열처리(In-Situ Post Heating) 효과", 대한금속·재료학회지, 57(8), pp.543~553 (2019), 대한금속·재료학회[DOI]
- J. Mazumder, , Opt. Lasers Eng, 34, pp.397~ (2000)
- N. K. Adomako, , Mater. Res. Lett, 7, pp.259~ (2019)
- T. Allen, , Mater. Today, 13, pp.14~ (2010)
- 이종훈, "니켈 합금 모재 및 용접재의 일차수응력부식균열 균열성장속도 시험", CORROSION SCIENCE AND TECHNOLOGY, 18(1), pp.33~38 (2019), 한국부식방식학회[DOI]
- S. S. Hwang, , J. Nucl. Mater, 443, pp.321~ (2013)
- V. N. Shah, , Nucl. Eng. Des, 134, pp.199~ (1992)
- G. S. Shin, , Korean J. Met. Mater, 58, pp.782~ (2020)
- 신기승, "고에너지 직접 적층법으로 제조된 경사조성재료의 미세조직 및 경도 변화에 미치는 후열처리 영향 연구", 대한금속·재료학회지, 59(2), pp.81~98 (2021), 대한금속·재료학회
- Bassiouny Saleh, "Review on the Influence of Different Reinforcements on the Microstructure and Wear Behavior of Functionally Graded Aluminum Matrix Composites by Centrifugal Casting", Metals and Materials International, 26(7), pp.933~960 (2020), 대한금속·재료학회[DOI]
- Guangming Zheng, "Microstructural and Mechanical Properties of TiCX–Ni3(Al,Ti)", Ni Functionally Graded Composites Fabricated from Ti3AlC2 and Ni Powders, 2020, pp.26(6), 905~913[DOI]
- S. M. Catherine, , J. Mater. Process. Technol, 268, pp.171~ (2019)
- Fatemeh Khaleghi, "Functionally-Graded Shape Memory Alloy by Diffusion Annealing of Palladium-Coated NiTi Plates", Metals and Materials International, 23(5), pp.915~922 (2017), 대한금속·재료학회[DOI]
- N. K. Adomako, , Mater. Sci. Eng., A, 732, pp.378~ (2018)
- N. K. Adomako, , Mater. Sci. Eng., A, 753, pp.208~ (2019)
- B. Kieback, , Sci. Eng., A, 362, pp.81~ (2003)
- B. Onuike, , Addit. Manuf, 22, pp.844~ (2018)
- 김종식, "316L 스테인리스강에서 마르텐사이트 생성거동에 미치는 가공열처리의 영향", 대한금속·재료학회지, 56(4), pp.265~271 (2018), 대한금속·재료학회[DOI]