단면 겹치기 접착 조인트의 충돌해석
An Impact Analysis of Adhesively-Bonded Single Lap Joint
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
This study presents an explicit dynamic analysis of an adhesively bonded single-lap joint under an impact load. The finite element software, ANSYS LS-DYNA, was used for the analysis and Von Mises stresses were obtained from the analysis. To model the adherents, solid elements were used and a rigid body was assumed for impactor modeling. Three impact heights (1 m, 5 m, and 10 m) were applied to consider different impact conditions and infinite boundary conditions were applied to the end-area of each adherent to save computational time in the analysis. In addition to investigating the stresses in the normal state, we also investigated the stresses in a damaged state (elasticity deterioration),simulated by a change in Young's modulus for 36 of the 3600 elements in the upper layer of the adhesive. The results showed that the location of damage is critical to the stress state of each layer (upper, middle, and lower).
Abstract
This study presents an explicit dynamic analysis of an adhesively bonded single-lap joint under an impact load. The finite element software, ANSYS LS-DYNA, was used for the analysis and Von Mises stresses were obtained from the analysis. To model the adherents, solid elements were used and a rigid body was assumed for impactor modeling. Three impact heights (1 m, 5 m, and 10 m) were applied to consider different impact conditions and infinite boundary conditions were applied to the end-area of each adherent to save computational time in the analysis. In addition to investigating the stresses in the normal state, we also investigated the stresses in a damaged state (elasticity deterioration),simulated by a change in Young's modulus for 36 of the 3600 elements in the upper layer of the adhesive. The results showed that the location of damage is critical to the stress state of each layer (upper, middle, and lower).
참고문헌 (17)
- 김현중, "에폭시수지 접착제의 특성과 응용", 접착 및 계면, 기술강좌(3), 2(2), pp.35~47 (2001)
- 박성완, "접착이음의 강도평가에 대한 해석", 한국공작기계학회 2004 추계학술대회, pp.98~107 (2004), 한국공작기계학회
- 안석환, "저속충격에 의한 복합재료 적층판의 손상", 한국해양공학회지, 19(1), pp.39~43 (2005), 한국해양공학회
- 유종선, "접착과 접착 메커니즘", 접착 및 계면,기술강좌(1), 1(1), pp.63~72 (2000)
- 오승규, "이원", 대한기계학회지, 22(5), pp.32~37 (2004)
- 이영상, "실험계획법을 이용한 아크릴 점착제의 점착력 최적화", 접착 및 계면, 9(1), pp.22~27 (2008), 한국접착및계면학회
- 이원, "피착체의 두께가 다른 단순겹치기 접착이음에 대한 응력특이성 파라미터의 해석", 한국자동차공학회 1995년 춘계학술대회, pp.16~22 (1995), 한국자동차공학회
- Andruet, R.H, "Twoand Three-dimensional Geometrical Nonlinear Finite Elements for Analysis of Adhesive Joints", International Journal of Adhesion & Adhesives, 21, pp.17~34 (2001)
- Avila, A.F, "Stress Analysis on a Wavy-lap Bonded Joint for Composites", International Journal of Adhesion & Adhesives, 24, pp.407~414 (2004)
- Carpenter, W.C, "Two Finite Elements for Modeling the Adhesive in Bonded Configuration", Journal of Adhesives, 30, pp.25~46 (1989)
- Gonçalves, J.P.M, "A Three-Dimensional Finite Element Models for Stress Analysis of Adhesive Joints", International Journal of Adhesion & Adhesives, 22, pp.357~365 (2002)
- Mark Hellmanns, "Manual Application of Adhesives", 접착 및 계면, 7(4), pp.24~27 (2006), 한국접착및계면학회
- Li, G, "Finite Element and Experimental Studies on Single-Lap Balanced Joints in Tension", International Journal of Adhesion & Adhesives, 21, pp.211~220 (2001)
- Lucas F M da Silva, "Influence of the Adhesive, the Adherend and the Overlap on the Single Lap Shear Strength", 접착 및 계면, 7(4), pp.1~9 (2006), 한국접착및계면학회
- Richardson, G, "A Comparison of Two and Three-dimensional Finite Element Analysis of Adhesive Joints", International Journal of Adhesion & Adhesives, 13, pp.193~200 (1993)
- Symietz, D, "High-performing Adhesive Bonding Fastening Technique For Automotive Body Structures", Journal of Adhesion and Interface, 7(4), pp.60~64 (2006)
- Wooley, G.R, "Stress Concentration Factors for Bonded Lap Joint", Journal of Aircraft, 8, pp.817~820 (1971)