스팀사출성형에 의한 공정의 최적화
Process optimization for the steam injection molding
2
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
The water has been the suitable for the cooling medium until now. But the water as cooling medium seem to have the limit for high speed injection. The steam plastic molding injection use the steam as the medium when raise the mold temperature. The weld line has been the major quality problems in a plastic injection parts to be difficult to be solved. These problems in injection-molded plastic parts are difficult to find the reason because these issues are usually in tradeoff realtions with each other. The purpose of this paper is to obtain the optimum injection moulding condition for improving the quality of plastic injection parts and to inquire the productivity improvement with the measured cycle time by steam plastic moluding injection. Based on these numerical results, the guidelines of mould design and injection processing condition were established. As a result, the improvement of quality and the reduction of cycle time was achieved.
Abstract
The water has been the suitable for the cooling medium until now. But the water as cooling medium seem to have the limit for high speed injection. The steam plastic molding injection use the steam as the medium when raise the mold temperature. The weld line has been the major quality problems in a plastic injection parts to be difficult to be solved. These problems in injection-molded plastic parts are difficult to find the reason because these issues are usually in tradeoff realtions with each other. The purpose of this paper is to obtain the optimum injection moulding condition for improving the quality of plastic injection parts and to inquire the productivity improvement with the measured cycle time by steam plastic moluding injection. Based on these numerical results, the guidelines of mould design and injection processing condition were established. As a result, the improvement of quality and the reduction of cycle time was achieved.
참고문헌 (11)
- 박근, "급속 금형가열에 의한 박육 사출성형의 유동특성 개선에 관한 연구", 소성가공, 15(1), pp.15~20 (2006), 한국소성가공학회
- Satou Athusi, "The sum of the mould for ultrsonic injection moulding", Die & Mold Technology, 2 (2003), Chomdan co.
- An introduction for HighCycle Injection moulding, "Tuyu Agaotuto", A committee of inquiry into Japan industry, ~ (1997)
- O.R.Kim, "A study on the performance Evaluation of Injection of Thin Wall Molding", Doctorate, pp.2010
- 안동규, "고속 냉각 특성을 가진 사출성형 금형 코어 제작 및 사출 성형", 소성가공, 16(7), pp.549~554 (2007), 한국소성가공학회
- 강중근, "공정 모니터링 시스템을 이용한 최적 사출 조건 설정", 소성가공, 16(1), pp.54~60 (2007), 한국소성가공학회
- Yunus A. Cengel, "Thermodynamics an engineering approach" (2007), McGrowHill
- Bruce.R Gregg, "Modern Materials and Manufacturing" (2005), Process Prentice-Hall, Inc.
- 문영대, "Flat TV Front Cover의 Gas 사출 금형에 대한 연구", 소성가공, 12(8), pp.738~743 (2003), 한국소성가공학회
- 조재성, "가스사출성형을 이용한 TV MASK FRONT의 무도장 제품에 관한 연구", 소성가공, 11(8), pp.691~700 (2002), 한국소성가공학회
- J. C. Park, "Automatic Mold Design Methodology to Optimize Warpage and Weld Line in Injection Molded Parts", Trans. Mater. Proc., 9, pp.512~525 (2000)