자동차 부품의 강성 보강을 위한 섬유강화 플라스틱 사출성형품의 섬유 배향 및 기계적 특성에 관한 연구
A study on the fiber orientation and mechanical characteristics of injection molded fiber-reinforced plastic for the rigidity improvement of automotive parts
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Fiber-reinforced plastics(FRPs) have excellent specific stiffness and strength, so they are usually used as automotive parts that require high rigidity and lightweight instead of metal. However, it is difficult to predict the mechanical properties of injection molded parts due to the fiber orientation and breakage of FRPs. In this paper, the fiber orientation characteristics and mechanical properties of injection molded specimens were evaluated in order to fabricate automotive transmission side covers with FRPs and design a rib structure for improvement of their rigidity. The test molds were designed and manufactured to confirm the fiber orientation characteristics of each position of the injection molded standard plate-shaped specimens, and the tensile properties of the specimens were evaluated according to the injection molding conditions and directions of specimens. A gusset-rib structure was designed to improve the additional structural rigidity of the target products, and a proper rib structure was selected through the flexural tests of the rib-structured specimens. Based on the evaluation of fiber orientation and mechanical characteristics, the optimization analyses of gate location were performed to minimize the warpage of target products. Also, the deformation analyses against the internal pressure of target product were performed to confirm the rigidity improvement by gusset-rib structure. As a result, it could be confirmed that the deformation was reduced by 27~37% compared to the previous model, when the gusset-rib structure was applied to the joining part of the target products.
Abstract
Fiber-reinforced plastics(FRPs) have excellent specific stiffness and strength, so they are usually used as automotive parts that require high rigidity and lightweight instead of metal. However, it is difficult to predict the mechanical properties of injection molded parts due to the fiber orientation and breakage of FRPs. In this paper, the fiber orientation characteristics and mechanical properties of injection molded specimens were evaluated in order to fabricate automotive transmission side covers with FRPs and design a rib structure for improvement of their rigidity. The test molds were designed and manufactured to confirm the fiber orientation characteristics of each position of the injection molded standard plate-shaped specimens, and the tensile properties of the specimens were evaluated according to the injection molding conditions and directions of specimens. A gusset-rib structure was designed to improve the additional structural rigidity of the target products, and a proper rib structure was selected through the flexural tests of the rib-structured specimens. Based on the evaluation of fiber orientation and mechanical characteristics, the optimization analyses of gate location were performed to minimize the warpage of target products. Also, the deformation analyses against the internal pressure of target product were performed to confirm the rigidity improvement by gusset-rib structure. As a result, it could be confirmed that the deformation was reduced by 27~37% compared to the previous model, when the gusset-rib structure was applied to the joining part of the target products.
참고문헌 (18)
- J. Walker, "Effect of Multi-speed Transmission Design on the Drive Cycle Performance of a Series-parallel Hybrid Electric Vehicle", Powertrains, 11(1), pp.90~ (2022)
- X. Xu, "Comparative Study on Fuel Saving Potential of Series-parallel Hybrid Transmission and Series Hybrid Transmission", Energy Conversion and Management, 252(15), pp.114970~ (2022)
- G. Steyer, "Transmission Side Cover Design Optimization for NVH Part1 : Shell Curvature Studies", Passenger Cars : Part 2, 160(6), pp.3118~3124 (1997)
- C. H. Chung, "Transmission Side Cover Design Optimization for NVH Part2 : Geometric Optimization Studies", Passenger Cars : Part 2, 160(6), pp.3124~3130 (1997)
- The Use of Pre-Test Analysis Procedures for FE Model, "Test Correlation of a Transmission Side Cover", M. Donley, 1997, Technical Paper, 972023
- F. Rezaei, "Development of Short-carbon-fiber-reinforced Polypropylene Composite for Car Bonnet", Polymer – Plastics Technology and Engineering, 47(4), pp.351~357 (2008)
- D. Rajak, "Fiber-reinforced Polymer Composites : Manufacturing, Properties, and Applications", Polymers, 11(10) (2019)
- H. Ning, "A Review of Long Fiber Thermoplastic(LFT)Composites", International Materials Reviews, 65(3), pp.164~188 (2002)
- H. Bijsterbosch, "Polyamide 6-Long Glass Fiber Injection Moldings", Polymer Composites, 16(5), pp.363~369 (1995)
- S. Fu, "Tensile Properties of Short-glass-fiber-and Short-carbon-fiber-reinforced Polypropylene", Composites Part A : Applied Science and Manufacturing, 31, pp.1117~1125 (2000)
- J. Denault, "Tensile Properties of Injection Molded Long Fiber Thermoplastic Composites", Polymer Composites, 10(5), pp.313~321 (1989)
- T. V. Khanh, "The Effects of Injection Molding on the Mechanical Behavior of Long-Fiber Reinforced PBT", PET Blends, 1991, pp.40, 423~435
- M. Mashimoto, "Prediction of Tensile Strength of Discontinuous Carbon Fiber", Polypropylene Composite with Fiber Orientation Distribution, 2012, pp.43(10), 1791~1799
- S. Barbosa, "Analysis of the Relationship between Processing Conditions-Fiber Orientation-Final Properties in Short Fiber Reinforced Polypropylene", Reinforced Plastics and Composites, 18(5), pp.413~420 (1999)
- S. Yang, "Mechanical Properties of Aligned Long Glass Fiber Reinforced Polypropylene 1 : Tensile Strength", Polymer Composites, 20(2), pp.200~206 (1999)
- S. Mortazavian, "Effects of Fiber Orientation and Anisotropy on Tensile Strength and Elastic Modulus of Short Fiber Reinforced Polymer Composites", Composites Part B : Engineering, 72, pp.116~129 (2015)
- H. Zhu, "Fiber Distribution of Long Fiber Reinforced Polyamide and Effect of Fiber Orientation on Mechanical Behavior", Polymer Composites, 41(4), pp.1531~1550 (2020)
- R. Nobe, "Effects of SFC Content, Injection Speed, and CF Content on the Morphology and Tensile Properties of Microcellular Injection-Molded CF", PP Composites, 2019, pp.59(7), 1371~1380