치과보철용 Ni-Cr-Ti 소결체합금의 포셀린결합력 및 기계적 특성
Porcelain Bonding Strength and Mechanical Properties of Sintered Ni-Cr-Ti Alloy for Dental Prosthodontics
1
조회
0
다운로드
3
인용
0
참고문헌
키워드
초록
In this study, porcelain bonding strength and mechanical properties of sintered Ni-Cr-Ti alloy for dental prosthodontics have been researched experimentally. Mechanical and morphological characteristics of the alloys were examined by Vickers hardness test, tensile and bonding strength test, surface roughness test, field-emission scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction. In the sintered Ni-13Cr-xTi alloys, morphology of sintered alloy showed porous matrix diffused with alloying elements of Cr and Ti, and showed dendritic structure after melting process. From the XRD results, the second phases of NiCr, Ni3Cr, and Ni3Ti were formed in the case of sintered and melted Ni-13Cr-xTi alloys. The tensile strength and hardness of Ni-13Cr-xTi alloys increased, as Ti content increased. Surface roughness increased, as Ti content increased. The bonding strength between metal and porcelain of Ni-13Cr-5Ti alloy was higher than those of Ni-13Cr and Ni-13Cr-10Ti alloys.
Abstract
In this study, porcelain bonding strength and mechanical properties of sintered Ni-Cr-Ti alloy for dental prosthodontics have been researched experimentally. Mechanical and morphological characteristics of the alloys were examined by Vickers hardness test, tensile and bonding strength test, surface roughness test, field-emission scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction. In the sintered Ni-13Cr-xTi alloys, morphology of sintered alloy showed porous matrix diffused with alloying elements of Cr and Ti, and showed dendritic structure after melting process. From the XRD results, the second phases of NiCr, Ni3Cr, and Ni3Ti were formed in the case of sintered and melted Ni-13Cr-xTi alloys. The tensile strength and hardness of Ni-13Cr-xTi alloys increased, as Ti content increased. Surface roughness increased, as Ti content increased. The bonding strength between metal and porcelain of Ni-13Cr-5Ti alloy was higher than those of Ni-13Cr and Ni-13Cr-10Ti alloys.
참고문헌 (14)
- U. J. Choi, "A study on how cyclic casting of base metal alloy for dental ceramic crown may effects upon lts mechanical properties and microstructure", J Kor Aca Den Tech, 25, pp.9~20 (2003)
- C. Y. Kim, "A study on EPMA on Ni-Cr alloy by Nb content for porcelain fused to metal crown", J Kor Aca Den Tech, 28, pp.19~26 (2006)
- 안재석, "도재용착용 Ni-Cr 합금과 Co-Cr 합금의 열처리에 따른 전단결합강도 비교", 대한치과기공학회지, 33(3), pp.185~192 (2011), 대한치과기공학회
- J. R. Bauer, "Microhardness of Ni-Cr alloys under different casting conditions", Braz Oral Res, 20, pp.40~46 (2006)
- H. Y. Lina, "Metallurgicalm surface, and corrosion analysis of Ni-Cr dental casting alloys before and after porcelain firing", Dent Mater, 24, pp.378~385 (2008)
- F. Faot, "Microstructural characterization of Ni-Cr-Mo-Ti and Ti-6Al-4V alloys used in prosthetic abutments", Rev. odonto cienc, 24, pp.401~405 (2009)
- N. J. Kim, "A comparison of marginal fitness by dental alloys", J Kor Aca Den Tech, 25, pp.29~40 (2003)
- 조미향, "다목적용 치과용 금합금의 소성 시 냉각속도와 계류시간에 따른 경도와 미세구조의 변화", 대한치과기공학회지, 33(4), pp.271~282 (2011), 대한치과기공학회
- K. J. Anusavice, "Phillips’ science of dental materials", pp.78~79 (2003), Saunders
- H. F. Morris, "The influence of heat treatment on several types of base-metal removable partial denture alloys", J Prosthet Dent, 41, pp.388~395 (1979)
- J. R. Strub, "Heat treatment, microstructure and corrosion of a low-gold casting alloy", J Oral Rehabil, 13, pp.521~528 (1986)
- Hyun Su Kim, "Corrosion Behaviors and Biocompatibility of the Ni-Cr-Mo Dental Casting Alloy", 대한금속·재료학회지, 52(1), pp.67~72 (2014), 대한금속·재료학회[DOI]
- V. S. Saji, "Electrochemical behavior of Co-Cr and Ni-Cr dental cast alloys", Trans. Nonferrous Met. Soc. China, 19, pp.785~790 (2009)
- 정인성, "베릴륨이 포함되지 않은 도재용착용 비귀금속 합금과 세라믹간의 전단결합강도와 계면특성", 한국콘텐츠학회 논문지, 10(11), pp.228~234 (2010), 한국콘텐츠학회