다양한 그루브 단면형상에 대한 스풀밸브의 윤활특성 연구
Study on Lubrication Characteristics of Spool Valve with Various Cross-sectional Groove Shapes
0
조회
0
다운로드
4
인용
0
참고문헌
키워드
초록
In this research, the lubrication characteristics of spool valves with various cross-sectional groove shapes were studied. The validity of using the Reynolds equation for the analysis of spool valves with various groove shapes was also investigated. The cross-sectional shapes for the grooves included a triangle, square, and U shape. The characteristics of the flow in the groove were investigated using streamlines. When the number of grooves was increased, the difference between the results obtained from the Reynolds equation and those obtained from the Navier-Stokes equation increased according to the groove shape. Thus, it was found that the Navier-Stokes equation should be used to investigate the lubrication characteristics of the spool valves in those cases. Moreover, in the case where the cross section of the groove was U-shaped, the groove prevented the small eddy current from occurring in the groove. Therefore, the lateral force and friction force of the spool valve with the U-shaped groove were lower than those of the spool valves with other groove shapes.
Abstract
In this research, the lubrication characteristics of spool valves with various cross-sectional groove shapes were studied. The validity of using the Reynolds equation for the analysis of spool valves with various groove shapes was also investigated. The cross-sectional shapes for the grooves included a triangle, square, and U shape. The characteristics of the flow in the groove were investigated using streamlines. When the number of grooves was increased, the difference between the results obtained from the Reynolds equation and those obtained from the Navier-Stokes equation increased according to the groove shape. Thus, it was found that the Navier-Stokes equation should be used to investigate the lubrication characteristics of the spool valves in those cases. Moreover, in the case where the cross section of the groove was U-shaped, the groove prevented the small eddy current from occurring in the groove. Therefore, the lateral force and friction force of the spool valve with the U-shaped groove were lower than those of the spool valves with other groove shapes.
참고문헌 (13)
- Tichy, J. A., "Plain Slider Bearing Load Due to Fluid Inertia-Experiment and Theory", Journal of Tribology, 107, pp.32~38 (1985)
- Arghir, M., "Theoretical Analysis of the Incompressible Laminar Flow in Macro-Roughness Cell", Journal of Tribology, 125, pp.309~318 (2003)
- Odyck van, D. E. A., "Stokes Flow in Thin Films", Journal of Tribology, 125, pp.121~134 (2003)
- DongJooSong, "A Comparison study Between Navier-Stokes Equation and Reynolds Equation in Lubricating Flow Regime", Journal of Mechanical Science and Technology, 17(4), pp.599~605 (2003), 대한기계학회
- Guardino, C., "Calculation of Surface Roughness Effects on Air-Riding Seals", ASME J. Eng. Gas Turbines Power, 126, pp.75~82 (2004)
- Sahlin, F., "Two-Dimensional CFD Analysis of Micro- Patterned Surfaces in Hydrodynamic Lubrication", Journal of Tribology, 127, pp.96~102 (2005)
- Odyck van, D. E. A., "Compressible Stokes Flow in Thin Films", Journal of Tribology, 125, pp.543~551 (2003)
- Li, J., "Evaluation on Applicability of Reynolds Equation for Squared Transverse Roughness Compared to CFD", Journal of Tribology, 129, pp.963~967 (2007)
- Dobrica, M. B., "About the Validity of Reynolds Equation and Inertia Effects in textured Sliders of Infinite Width", Proc. IMechE., 223, pp.69~78 (2009)
- 홍성호, "캐비테이션을 고려한 스풀밸브 해석에서 Navier-Stokes 방정식과 Reynolds 방정식에 의한 비교 연구", 한국윤활학회지, 29(5), pp.275~285 (2013), 한국윤활학회[DOI]
- Cheng, M., "Vortex Structure of Steady Flow in a Rectangular Cavity", Computers & Fluids, 35, pp.1046~1062 (2006)
- Shankar, P. N., "Fluid Mechanics in the Driven Cavity", Annu. Rev. Fluid Mech., 32, pp.93~136 (2000)
- 박태조, "Groove 단면형상에 따른 유압 Spool Valve의 윤활해석", 한국윤활학회지, 25(1), pp.13~19 (2009), 한국윤활학회