250 kW급 초임계 CO2 발전용 감속기의 유체윤활 베어링 및 회전체 동역학 특성 해석
Bearing and Rotordynamic Performance Analysis of a 250 kW Reduction Gear System
0
조회
0
다운로드
4
인용
0
참고문헌
키워드
초록
This paper presents a rotordynamic analysis of the reduction gear system applied to the 250 kW super critical CO2 cycle. The reduction gear system consists of an input shaft, intermediate shaft, and output shaft. Because of the high rotating speed of the input shaft, we install tilting pad bearings, rolloer bearings support the intermediate and output shafts. To predict the tilting pad bearing performance, we calculate the applied loads to the tilting pad bearings by considering the reaction forces from the gear. In the rotordynamic analysis, gear mesh stiffness results in a coupling effect between the lateral and torsional vibrations. The predicted Campbell diagram shows that there is not a critical speed lower than the rated speed of 30,000 rpm of the input shaft. The predicted modes on the critical speeds are the combined bending modes of the intermediate and output shaft, and the lateral vibrations dominate when compared to the torsional vibrations. The damped natural frequency does not strongly depend on the rotating speeds, owing to the relatively low rotating speed of the intermediate and output shaft and constant stiffness of the roller bearing. In addition, the logarithmic decrements of all the modes are positive; therefore all modes are stable.
Abstract
This paper presents a rotordynamic analysis of the reduction gear system applied to the 250 kW super critical CO2 cycle. The reduction gear system consists of an input shaft, intermediate shaft, and output shaft. Because of the high rotating speed of the input shaft, we install tilting pad bearings, rolloer bearings support the intermediate and output shafts. To predict the tilting pad bearing performance, we calculate the applied loads to the tilting pad bearings by considering the reaction forces from the gear. In the rotordynamic analysis, gear mesh stiffness results in a coupling effect between the lateral and torsional vibrations. The predicted Campbell diagram shows that there is not a critical speed lower than the rated speed of 30,000 rpm of the input shaft. The predicted modes on the critical speeds are the combined bending modes of the intermediate and output shaft, and the lateral vibrations dominate when compared to the torsional vibrations. The damped natural frequency does not strongly depend on the rotating speeds, owing to the relatively low rotating speed of the intermediate and output shaft and constant stiffness of the roller bearing. In addition, the logarithmic decrements of all the modes are positive; therefore all modes are stable.
참고문헌 (9)
- Dostal, V., "A supercritical carbon dioxide cycle for next generation nuclear reactors", Doctor, pp.2004
- Turchi, C., "Thermodynamic study of advanced supercritical carbon dioxide power cycles for concentrating solar power systems", J. of Sol. Energy Eng, 135, pp.041007~ (2013)
- Kus, B., "Development of one-dimensional model for initial design and evaluation of oil-free CO2 turbo-compressor", Int. J. of Refrig, 134, pp.2079~2090 (2013)
- Pecnik, R., "Computational fluid dynamics of radial compressor operating with supercritical CO2", J. of Eng. Gas Turbines and Power, 134, pp.122301~ (2013)
- Ettles, C., "The analysis and performance of pivoted pad journal bearings considering thermal and elastic effects", J. of Lub. Tech, 102, pp.182~192 (1980)
- Desbordes, H., "Dynamic analysis of tilting pad journal bearing-Influence of pad deformations", J. of Tribol, 116, pp.621~628 (1994)
- Rouch, K. E., "Dynamics of pivoted-pad journal bearing, including pad translation and rotation effects", J. of Lub. Tech, 26, pp.102~109 (1983)
- Chen, W. J., "Introduction to Dynamics of Rotor Bearing Systmes" (2007), Eigen Technologies
- Chen, W. J., "Practical Rotordynamics and Fluid Film Bearing Design" (2015), Eigen Technologies