정압 베어링을 적용한 초임계 CO2 발전용 펌프-구동 터빈 개발
Development of Pump-Drive Turbine with Hydrostatic Bearingfor Supercritical CO2 Power Cycle Application
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
In this paper, we present a hydrostatic bearing design and rotordynamic analysis of a pump-and-drive turbine module for a 250-kW supercritical CO2 cycle application. The pump-and-drive turbine module consists of the pump and turbine wheel, assembled to a shaft supported by two hydrostatic radial and thrust bearings. The rated speed is 21,000 rpm and the rated power is 143 kW. For the bearing operation, we use high-pressure CO2as the lubricant, which is supplied to the bearing through the orifice restrictor. We calculate the bearing stiffness and flow rate for various orifice diameters, and then select the diameter that provides the maximum bearing stiffness. We also conduct a rotordynamic analysis based on the design parameters of the pump-and-drive turbine module. The predicted Campbell diagram shows that there is no critical speed below the rated speed, owing to the high stiffness of the bearings. Furthermore, the predicted damping ratio indicates that there is no unstable mode. We conduct the operating tests for the pump and drive turbine modules within the supercritical CO2 cycle test loop. The pressurized CO2, at a temperature of 136°C, is supplied to the turbine and we monitor the shaft vibration during the test. The test results show that there is no critical speed below the rated speed, and the shaft vibration is controlled to below 3 μm.
Abstract
In this paper, we present a hydrostatic bearing design and rotordynamic analysis of a pump-and-drive turbine module for a 250-kW supercritical CO2 cycle application. The pump-and-drive turbine module consists of the pump and turbine wheel, assembled to a shaft supported by two hydrostatic radial and thrust bearings. The rated speed is 21,000 rpm and the rated power is 143 kW. For the bearing operation, we use high-pressure CO2as the lubricant, which is supplied to the bearing through the orifice restrictor. We calculate the bearing stiffness and flow rate for various orifice diameters, and then select the diameter that provides the maximum bearing stiffness. We also conduct a rotordynamic analysis based on the design parameters of the pump-and-drive turbine module. The predicted Campbell diagram shows that there is no critical speed below the rated speed, owing to the high stiffness of the bearings. Furthermore, the predicted damping ratio indicates that there is no unstable mode. We conduct the operating tests for the pump and drive turbine modules within the supercritical CO2 cycle test loop. The pressurized CO2, at a temperature of 136°C, is supplied to the turbine and we monitor the shaft vibration during the test. The test results show that there is no critical speed below the rated speed, and the shaft vibration is controlled to below 3 μm.
참고문헌 (17)
- Conboy, T., "Performance Characteristics of an Operating Supercritical CO2 Brayton Cycle", J. Eng. Gas Turbines and Power, 134, pp.111703~ (2012)
- Conboy, T., "Control of a Supercritical CO2 Recompression Brayton Cycle Demonstration Loop", J. Eng. Gas Turbines and Power, 135, pp.111710~ (2013)
- Kimball, K. J., "Supercritical Carbon Dioxide Brayton Power Cycle Development Overview", TurboExpo (2012)
- Rowe, W. B., "Optimisation of Externally Pressurized Bearings for Minimum Power and Low Temperature", Triboiogy Int, 3, pp.153~157 (1970)
- Singh, D. V., "Static and Dynamic Analysis of Capillary Compensated Hydrostatic Journal Bearings by Finite Element Method", J. Lub. Tech, 99, pp.478~484 (1977)
- Ghosh, M. K., "Dynamic Characteristic of Multirecess Externally Pressurized Oil Journal Bearing", J. Lub. Tech, 100, pp.467~471 (1978)
- Rowe, W. B., "Dynamic and Static Properties of Recessed Hydrostatic Journal Bearings by Small Displacement Analysis", J. Lub. Tech, 102, pp.71~79 (1980)
- Chen, Y. S., "Stability of Multirecess Hybrid-Operating Oil Journal Bearings", J. Lub. Tech, 107, pp.116~121 (1985)
- Rhode, S. M., "On the Dynamic Behavior of Hybrid Journal Bearings", J. Lub. Tech, 98, pp.90~94 (1976)
- Ghosh, M. K., "Recess Volume Fluid Compressibility Effect on the DynamicCharacteristics of Multirecess Hydrostatic Journal Bearings with Journal Rotation", J. Tribol, 109, pp.417~426 (1987)
- Heller, S., "Static and Dynamic Performance of Externally Pressurized Fluid Film Journal Bearings in the Turbulent Regime", J. Lub. Tech, 95, pp.381~399 (1974)
- 김성기, "극저온 정압 저널베어링 성능해석에 관한 연구", 한국트라이볼로지학회지, 19(3), pp.139~145 (2003), 한국트라이볼로지학회
- Andress, L. S., "Approximate Analysis of Turbulent Hybrid Bearings. Static and Dynamic Performance for Centered Operation", J. Tribol, 112, pp.692~698 (1990)
- Ghosh, M. K., "Rotordynamic Characteristics of Multilobe Hybrid Bearings with Short Sills-Part I", Tribology Int, 36, pp.625~632 (2003)
- Ghosh, M. K., "Stability of Multilobe Hybrid Bearing with Short Sills-Part II", Tribology Int, 36, pp.633~636 (2003)
- Ren, T., "Stability Analysis of Water-Lubricated Journal Bearings for Fuel Cell Vehicle Air Compressor", Tribology Int, 95, pp.342~348 (2016)
- Jialei DU, "Dynamic coefficients and stability analysis of a water-lubricated hydrostatic bearing by solving the uncoupled Reynolds equation", Chinese Journal of Aeronautics, 33(8), pp.2110~2122 (2020), Elsevier BV[DOI]