진공 열처리를 통한 Ag 인쇄 도선 균일성 향상과 이에 따른 발열 감소 및 고온 환경 내구성 연구
Study on Improving Uniformity of Ag Printed Electric Line through Vacuum Annealing and Resulting Reduction in Heat Generation and High-Temperature Environmental Durability
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Electronic printing processes are gaining attention as next-generation eco-friendly patterning processes that can replace conventional patterning processes in semiconductor manufacturing that cause harmful problems and large amounts of pollutants. In the formation of patterned thin films by the electronic printing process, the unevenness of the film caused by the coffee ring effect, affects the performance of the device, and requires the identification of a process method for uniform film formation. In this study, Ag ink was printed with a dispenser to form an electrical line, and a thin film was formed by splitting the solvent drying temperature for 5 min and the ambient heat treatment conditions for 5 min. The uniformity of the thin film was analyzed, and the voltage-heat generation characteristics of the electric line and the shape retention ability of the thin film in a high-temperature environment were examined according to the uniformity of the thin film. Vacuum-annealing could create a uniform thin film. When evaluating the heat generation characteristics using a maximum applied voltage of 5V, the electrical conduction for a uniform thin film showed 83.1°C, whereas the coffee ring effect caused the electrical conduction for a non-uniform thin film to show 105°C heat generation. This showed that electrical conduction with a uniform thin film resulted in a 26% reduction in heat generation characteristics. In addition, it was confirmed that the printed electrical line with a uniform thin film had little change in shape at high temperatures. This confirms that a uniform thin film can suppress the heat generation of the conductor and cause little deformation in high-temperature environments, so it can be used in various environments.
Abstract
Electronic printing processes are gaining attention as next-generation eco-friendly patterning processes that can replace conventional patterning processes in semiconductor manufacturing that cause harmful problems and large amounts of pollutants. In the formation of patterned thin films by the electronic printing process, the unevenness of the film caused by the coffee ring effect, affects the performance of the device, and requires the identification of a process method for uniform film formation. In this study, Ag ink was printed with a dispenser to form an electrical line, and a thin film was formed by splitting the solvent drying temperature for 5 min and the ambient heat treatment conditions for 5 min. The uniformity of the thin film was analyzed, and the voltage-heat generation characteristics of the electric line and the shape retention ability of the thin film in a high-temperature environment were examined according to the uniformity of the thin film. Vacuum-annealing could create a uniform thin film. When evaluating the heat generation characteristics using a maximum applied voltage of 5V, the electrical conduction for a uniform thin film showed 83.1°C, whereas the coffee ring effect caused the electrical conduction for a non-uniform thin film to show 105°C heat generation. This showed that electrical conduction with a uniform thin film resulted in a 26% reduction in heat generation characteristics. In addition, it was confirmed that the printed electrical line with a uniform thin film had little change in shape at high temperatures. This confirms that a uniform thin film can suppress the heat generation of the conductor and cause little deformation in high-temperature environments, so it can be used in various environments.
참고문헌 (29)
- Park, D. U., "Review on Potential Risk Factors in Wafer Fabrication Process of Semiconductor Industry", Korean Journal of Occupational and Environmental Medicine, 23(3), pp.333~342 (2011)[DOI]
- Lee, I. J., "Distribution and Risk Assessment of Perfluoroalkyl and Polyfluoroalkyl Substances (PFAS) in the South Han River", Journal of Environmental Analysis, Health and Toxicology, 27(1), pp.29~38 (2024)[DOI]
- Huang, S. Z., "Health Risk Assessment of Photoresists Used in an Optoelectronic Semiconductor Factory", Risk Analysis, 39(12), pp.2625~2639 (2019)[DOI]
- Eom, Y. S., "Emission Factors of Air Toxics from Semiconductor Manufacturing in Korea", Journal of the Air & Waste Management Association, 56(11), pp.1518~1524 (2006)[DOI]
- Seo, S., "Global Performance, Trends, and Challenges for Assessment and Management of Per- and Polyfluoroalkyl Substances (PFASs): A Critical Review", Journal of Environmental Analysis, Health and Toxicology, 27(1), pp.1~13 (2024)[DOI]
- Yasuyuki, K., "Experimental Study on Injecting Highly Viscous Liquids by Using a Reciprocating Needle Dispensing System", International Journal of Advanced Manufacturing Technology, 90, pp.2243~2250 (2017)[DOI]
- Thomas, T., "High Viscosity Paste Dosing for Microelectronic Applications", 49th International Symposium on Microelectronics, 2016(1), pp.000345~000350 (2016)
- Khirotdin, R. K., "Printing and Curing of Conductive Ink Track on Curvature Substrate using Fluid Dispensing System and Oven", Engineering Letters, 25(3), pp.336~341 (2017)
- Tanguy, L., "Pressure Driven and Regulated Dispenser for the Microliter Range", Proceedings of the 1st International Conference on Microfluidic Handling Systems, pp.50~53 (2012)
- Nguyen, Q. H., "The Design and Control of a Jetting Dispenser for Semiconductor Electronic Packaging Driven by a Piezostack and a Flexible Beam", Smart Materials and Structures, 17(6), pp.065028~ (2008)[DOI]
- Losleben, N., "Model Fluids Representing Aqueous in-vitro Diagnostic Reagents for the Development of Dispensing Systems", Drug Discovery Today, 18(21-22), pp.1035~1042 (2013)[DOI]
- Huang, B., "Fully Automated Dispensing System Based on Machine Vision", Applied Sciences, 13(16), pp.9206~ (2023)[DOI]
- Fukada, K., "Profile Control of Inkjet Printed Silver Electrodes and Their Application to Organic Transistors", ACS Applied Materials & Interfaces, 5(9), pp.3916~3920 (2013)[DOI]
- Liu, C., "Improved Performance of Inkjet-Printed Ag Source", Drain Electrodes for Organic Thin-Film Transistors by Overcoming the Coffee Ring Effects, 2017, pp.7(11), 115008~
- Jiang, C., "Coffee-Ring-Free Quantum Dot Thin Film Using Inkjet Printing from a Mixed-Solvent System on Modified ZnO Transport Layer for Light-Emitting Devices", ACS Applied Materials & Interfaces, 8(39), pp.26162~26168 (2016)[DOI]
- Sliz, R., "Taming the Coffee Ring Effect : Enhanced Thermal Control as a Method for Thin-Film Nanopatterning", Langmuir, 36(32), pp.9562~9570 (2020)[DOI]
- Shen, X., "Minimal Size of Coffee Ring Structure", The Journal of Physical Chemistry B, 14(16), pp.5269~5274 (2010)[DOI]
- Yen, T. M., "Reversing Coffee-Ring Effect by Laser-Induced Differential Evaporation", Scientific Reports, 8(1), pp.1~11 (2018)[DOI]
- Zhou, P., "High-Resolution and Controllable Nanodeposition Pattern of Ag Nanoparticles by Electrohydrodynamic Jet Printing Combined with Coffee Ring Effect", Advanced Materials Interfaces, 6(20) (2019)[DOI]
- Yunker, P. J., "Suppression of the Coffee-Ring Effect by Shape-Dependent Capillary Interactions", Nature, 476(7360), pp.308~311 (2011)[DOI]
- Howard, N. S., "Surfactant Control of Coffee Ring Formation in Carbon Nanotube Suspensions", Langmuir, 39(3), pp.929~941 (2023)[DOI]
- Balzarini, M. F., "Comparative Study of Hot Air and Vacuum Drying on the Drying Kinetics And Physicochemical Properties of Chicory Roots", Journal of food science and technology, 55, pp.4067~4078 (2018)[DOI]
- Ma, W., "Effect of Radio Frequency Vacuum Drying on Drying Characteristics and Physicochemical Quality of Codonopsis pilosula Slices", Agriculture, 14(9) (2024)[DOI]
- Kim, G. W., "Development of Uniform Ag Electrode and Heating Sensors Using Inkjet Printing Technology", Journal of Sensor Science and Technology, 33(1), pp.24~29 (2024)[DOI]
- Kang, S., "Fire in Your Hands: Understanding Thermal Behavior of Smartphones", The 25th Annual International Conference on Mobile Computing and Networking, pp.1~16 (2019)
- Almubarak. A. A., "The Effects of Heat on Electronic Components", Int. J. Eng. Res. Appl., 7(5), pp.52~57 (2017)[DOI]
- Semenov, O., "Impact of Self-Heating Effect on Long-Term Reliability and Performance Degradation in CMOS Circuits", IEEE Transactions on Device and Materials Reliability, 6(1), pp.17~27 (2006)[DOI]
- Hong. J. H., "Multi-layer Front Electrode Formation to Improve the Conversion Efficiency in Crystalline Silicon Solar Cell", Journal of the Korean Institute of Electrical and Electronic Material Engineers, 25(12), pp.1015~1020 (2012)[DOI]
- Min, K. H., "Fabrication and Properties of MIS Solar Cell by using Screen Printing Method", Korean Institute of information Technology, 12(1), pp.17~23 (2014)[DOI]